Hitachi Koki NV 100H Bedienungsanleitung Seite 10

English
does not exceed the specified limit. Note that
excessive pressure may affect overall performance,
service life, and safety.
2. Lock mechanism of the trigger
This device has a lock mechanism to prevent the
trigger from pulling.
Set the lock lever to "Lock" position to lock the trigger
in place.
To drive a nail, turn the lock lever to the "Free"
position. When not driving nails set the lever to the
"Lock" position (Fig. 2).
CAUTION
Keep the trigger locked at all times except when
driving nails.
3. Lubrication
(1) Be sure to lubricate this nailer at least twice a day. To
lubricate, pour 10 to 15 drops of oil into the air plug
before and after using this nailer. The oil applied
before use lubricates this nailer; the oil applied after
use prevents rust.
(2) It is recommended using the recommended oil (SHELL
TONNA). Other applicable oils are listed. Never mix
two or more types of different oils.
4. Load Nails
(1) Grip the nail guide and knob with finger.
Press the knob down and swing the nail guide open.
And open the magazine cover (Fig. 3).
(2) Adjust the position of the nail holder according to the
nail length (Fig. 4).
The nail will not feed smoothly if the nail holder is
not correctly adjusted (Fig. 5).
a. Turn the nail holder about 90 degrees
counterclockwise.
b. Slide in vertical direction possible.
Lift or lower the nail holder to accept different
length nails.
c. Adjust the plate to the nail length reference points
on the magazine cover and turn the nail holder 90
degrees clockwise until you hear "click".
(3) Place the nail coil into the magazine.
Uncoil enough nails to reach the driving hole (Fig. 6).
Insert the first nail into the driving hole and the
second nail between the two pawls of the feeder.
Fit the nail head in the guide slot (Fig. 7).
(4) Close the magazine cover first and swing the nail
guide closed (Fig. 8).
(5) Lock the knob correctly.
NOTE:
Be careful not to deform the collated wires and not to
disengage the nails with the guide surface.
Otherwise, the nail guide will not close correctly.
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a
work bench or floor. Also, never face the nail outlet
toward any part of a person.
NOTE:
Before loading the nails in the magazine, position the
nail holder according to the length of the nail. If the
nail holder position is not adjusted properly, nail
feed may jam. If the cover is forcibly closed without
adjusting the position of the nail holder, the nail
holder may be damaged.
10
HOW TO USE THE NAILER
CAUTION
Never use the head or body of this device as a hammer.
Take precautions to ensure the safety of persons in
the vicinity during operation.
1. Set the lock lever to "Free" position
Turn the lock lever and align it with the "Free" position
(Fig. 9).
2. How to drive nails
This device is equipped with a mechanism allowing
"intermittent operation" or "continuous operation"
for most effective use according to the type material
the nails will be driven into.
(1) Intermittent operation
Intermittent operation nail driving is used when the
finished appearance is important and when driving a
nail in a particular spot.
against the spot where you will drive the nail.
Drive the nails one at a time by pulling the trigger
(Fig. 10).
NOTE:
Use "intermittent operation" when you are aiming at
a particular spot to drive the nail.
(2) Continuous operation
To drive nails with contact drive:
trigger. Then press the nail dispenser up against
2
the spots you want, to drive the nails one after another
at those spots (Fig. 11).
NOTE:
In intermittent operation, you cannot drive nails with
the trigger still held down, by again pressing the
push-lever up against the target spot. To continually
drive nails one after another, release your finger
from the trigger and switch to "continuous operation".
If a nail driver placed on the floor (push-lever pressed
against the floor) is picked up while pulling the trigger,
the nail driver will shift to single shot and it may be
impossible to shoot nails even if the push-lever is
pressed against something. If that happens, release
your finger from the trigger and then try driving nails
again.
CAUTION
Exercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
NOTE:
Precautions on no-load operation.
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed "no-load operation". Such operation
may deteriorate the bumper, magazine, and nail feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all
nails should be removed after using this nailer.
After completing operation, put into the body about 2
cc oil through the hose joint to protect the tool from
rust.
Under low temperature conditions, the machine
sometimes does not operate correctly. Always operate
the machine at the appropriate ambient temperature.
3. Driving nails into steel plating
CAUTION
Use C-beam steel with a thickness of 3.2 mm or less.
Use hardened nails designed for use with steel plating.
Press the push-lever up
1
First, pull the
1
2