Only Use An Original Gardena Blade; Technical Data - Gardena PowerMax 30/18V P4A Betriebsanleitung

To replace the blade [ Fig. T1 / T2 ]:
DANGER! Risk of physical injury!
Cut injury when the blade turns and it is damaged, bent, out of
balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent, out
of balance or has chipped edges.
v Do not regrind the blade.
The GARDENA spare parts are available from your GARDENA dealer or
from the GARDENA service.
v Only use an original GARDENA Blade
For safety reasons, we recommend that the blade be replaced by
GARDENA Service or by an authorised GARDENA dealer.
1. Insert a screwdriver into one of the proviced holes at the bottom of
(28)
the housing .
The screwdriver thus serves as a stop for the blade.
(25)
2. Unscrew the blade bolt
Make sure that the spacer
3. Remove the blade bolt (25)
(27)
4. Remove the blade .
(27)
5. Put the new blade on the mower. The inscription on the knife
(this side to grass) must be visible.
6. Put the washer (26) and the blade bolt
(27)
7. Screw the new blade tight with the blade bolt
15 – 20 Nm). Do not over-torque.
Make sure that the spacer
8. Pull the screwdriver out of the mower.
Make sure that the screwdriver is removed before restarting the mower
again.
Problem Possible Cause
Engine is jammed and Motor is blocked.
makes a noise
Cutting height is too low.
Loud noises, the mower Screws on engine, its fixing
is rattling or on the mower chasing are
loose.
Mower runs unevenly or Blade is damaged / worn or the
vibrates strongly blade mounting is released.
Blade is very dirty.
Lawn is not cleanly mowed
Blade is blunt or damaged.
Cutting height is set too low.
Mower does not start Battery is empty.
or stops
Battery temperature is outside
the permissible temperature
range.
There are drops of water or
moisture between the battery
contacts on the mower.
Engine is blocked.
Product is defective.
Battery is not put completely
into the battery holder.
Safety key is not in positon 1.
Battery is defective.
Charging is not possible. The battery is not connected
Green battery charge (correctly).
(Lc)
indicator is continously
Battery contacts are dirty.
lit [ Fig. O3 ]
14630-20.960.03.indd 15 14630-20.960.03.indd 15
.
(24) is not damaged when applying the force.
and the washer (26) .
(25) on the mower.
(25)
(tightening torque is
(24) is not damaged when applying the force.
Remedy
v Remove the obstacle.
v Raise the cutting height.
v Let the screws be tightened
by an authorised specialist
dealer or the GARDENA
Service.
v Replace the blade
(see To replace the blade).
v Clean the mower
(see 4. MAINTENANCE).
If this does not rectify the
problem, contact the
GARDENA Service.
v Replace the blade
(see To replace the blade).
v Raise the cutting height.
v Charge the battery.
v Wait until the battery tem-
perature is between 0 °C –
+ 45 °C again.
v Remove the water drops /
moisture with a dry cloth.
v Remove the obstacle.
Start again.
v Contact the GARDENA
Service.
v Put the battery completely
into the battery holder until it
audibly engages.
v Turn the safety key to
position 1.
v Replace the battery.
v Connect battery to charger
correctly.
v Clean the battery contacts
(e. g. by connecting and
disconnecting the battery
several times. Replace the
battery if necessary.
Problem
Charging is not possible.
Green battery charge
(Lc)
indicator is continously
lit [ Fig. O3 ]
Green battery charge
(Lc)
indicator is not
illuminated
[ Fig. O3 ]
NOTE: For any other malfunctions please contact the GARDENA service depart-
Art. 4120
ment. Repairs must only be done by GARDENA service departments or specialist
dealers approved by GARDENA.

7. TECHNICAL DATA

Battery Lawnmower
Speed of rotation cutting
blade
Cutting width
Cutting height adjustment
(3 positions)
Volume of grass box
Weight (without Battery)
Sound pressure level L
1)
pA
Uncertainty k
pA
Sound power level L :
2)
WA
measured/guaranteed
Uncertainty k
WA
Hand/arm vibration a
1)
vhw
Uncertainty k
vhw
Measuring process complying with:
Note: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of
exposure. The vibration emission value can vary during actual use of the electric power
tool depending on the ways in which the machine is used. As a safety measure, you
should work with the machine for a maximum of 1 hour without interruption.
System Battery
PBA 18V 4.0Ah W-C
Battery voltage
Battery capacity
Number of cells (Li-Ion)
Appropriate POWER FOR ALL system Battery Chargers: AL 1810 CV / AL 1815 CV / AL 18V-20 /
AL 1830 CV / AL 1880 CV.
Battery Charger
AL 1810 CV P4A
Mains voltage
Mains frequency
Rated power
Battery charging voltage
Max. battery charging
current
Battery charging time
80 % / 97 – 100 % (approx.)
PBA 18V 2.0Ah W-B
PBA 18V 2.5Ah W-B
PBA 18V 4.0Ah W-C
Permitted charging
temperature range
Weight according to
EPTA-Procedure 01:2014
Protection class
Appropriate POWER FOR ALL system Batteries: PBA 18V.
Possible Cause Remedy
Battery temperature is outside v Wait until the battery tem-
the permissible charging tem- perature is between 0 °C –
perature range. + 45 °C again.
Battery is defective. v Replace the battery.
Mains plug of the charger is v Insert the mains plug into the
not (correctly) plugged in. mains socket (completely).
Socket outlet, mains cable or v Check the mains voltage.
charger is defective Let the charger be checked
if necessary by an authorised
specialist dealer or the
GARDENA Service.
Unit Value (Art. 14630)
rpm 3500
cm 30
mm 35, 50, 65
l 25
kg 8
73
dB (A)
3
87 / 89
dB (A)
0.7
≤ 2.5
m/s
2
1.5
EN IEC 62841-4-3 RL 2000/14/EC / S.I. 2001 No.1701
1) 2)
Unit Value (Art. 14905)
V (DC) 18
Ah 4.0
10
Unit Value (Art. 14900)
V (AC) 220 – 240
Hz 50 – 60
W 26
V (DC) 18
mA 1000
min. 96 / 124
min. 120 / 154
min. 192 / 244
°C 0 – 45
kg 0.17
/ II
15
25.07.22 11:59 25.07.22 11:59