Unpacking; Assembly / Before Commissioning - Scheppach SprayVac20 Original Bedienungsanleitung

8. Unpacking

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
9.

Assembly / Before commissioning

m ATTENTION!
Prior to use, ensure that the device has been correct-
ly and fully assembled.
Unpacking (Fig. 1, 2)
• Release the locking hooks (8) and remove the ma-
chine head with filter cage (3). The accessories are
located inside the stainless steel container (1). Only
the extension pipes (25) are located outside the
stainless steel container (1) in the packaging. Re-
move all of the accessories from the stainless steel
container (1).
Installation of the roller mounts (11 + 12) (Fig. 3)
1. Turn the stainless steel container (1) upside down.
(The machine head with filter cage (3) must be re-
moved.)
2. Slide the wheels (11) into the recesses provided on
the caster mounting base (13) and screw them in
place with the screws (30).
24 | GB
Installation of the castors (12) (Fig. 3)
Press the two deflection rollers (12) into the holes
1.
provided in the roller mounts (12a).
Installing the machine head with filter cage (3)
(Fig. 8)
Place the machine head with filter cage (3) on the
1.
stainless steel container (1).
2. Secure the machine head (3) with the locking
hooks (8). When installing the machine head with
filter cage (3), ensure that the locking hooks (8)
latch into place correctly. The water channel con-
nection (4) must be above the vacuum connection
(2).
Installing the filter (33) (Fig. 5, 6)
Never use the device without filter! Always ensure that
the filters are correctly fitted.
Installing the foam filter (33)
For wet vacuuming, open and remove the filter
1.
cage (3a) by turning it anti-clockwise (Fig. 6).
Pull off the clipped cover cap (3b) with a screw-
2.
driver (not included in the scope of delivery), pull
the foam filter (33) over the filter cage with safety
float valve (3c) and refit the cover cap (3b) (Fig. 5).
Now reinsert the filter cage by turning it clockwise
3.
(Fig. 6).
To avoid tearing the foam filter (33),
• only insert a dry filter
• knock the edge of the filter over a little to insert it and
then roll it back again.
Fit the folded filter (31) and foam filter (32) (not in-
cluded in the scope of delivery)
Open and remove the filter cage (3a) by turning it
1.
anti-clockwise (Fig. 6).
Insert the hepa filter (31) or foam filter (32) and re-
2.
place the filter cage by turning it clockwise (Fig. 6).
Installing the paper filter bag (34) (fig. 7)
It is recommended to use an additional paper filter bag
(34) when vacuuming fine, dry dirt.
Slide the paper filter bag (34) over the suction
1.
opening in the stainless steel container (1).
The paper filter bag (34) is only suitable for dry
vacuuming. The paper filter bag (34) makes it eas-
ier to dispose of the dust collected.
www.scheppach.com