Selecting The Mounting Location - Sygonix 2618633 Bedienungsanleitung

All (rechargeable) batteries should be replaced at the same time. Mixing old and new
(rechargeable) batteries in the device can lead to (rechargeable) battery leakage and
device damage.
(Rechargeable) batteries must not be dismantled, short-circuited or thrown into fire. Never
recharge nonrechargeable batteries. There is a risk of explosion!
6 Product overview
6.1 Fan
1 2 3
1 8 x Screws (KA3) 5 4 x Screws (TM5)
2 Front grille 6 Back grille
3 Blade cap 7 Motor shaft
4 Fan blades 8 Motor housing
6.2 Remote control and control panel
a
e b
d c
E
D
C
Remote control
a. On/Off button
b. Speed button
c. Oscillation button
d. Timer button
e. Mode button
7 Installing the batteries in the remote control
1. Open the battery compartment cover on the back of the remote control.
2. Insert the new batteries (2x 1.5 V AAA batteries, not included), following the + and - ends
indicated inside the compartment.
3. Close the battery compartment cover.
4 5 6 7
9 Mounting holes
10 Control panel
11 Remote control
Control panel
A. On/Off button
B. Speed button
C. Timer button
D. Oscillation button
E. Display
8 Assembling the fan
1. Unplug the product from the mains socket.
2. Hold the back grille (6) with the handle at the top and facing backwards. Insert the back
grille onto the motor shaft (7), making sure that it is properly aligned with the front of the
motor housing (8).
3. Tighten the 4 screws (TM5*8) (5) on the back grille (6) to secure it to the motor housing,
as illustrated.
4. Align the centre of the fan blades (4) with the 2 pins on the motor shaft (7) and push it in.
5. Tighten the blade cap (3) onto the motor shaft (7) by turning the cap anti-clockwise. Turn
the fan blades (4) a few turns with your hands to check that they are properly aligned and
8 9
turning smoothly.
6. Align and close the front grille (2) onto the back grille (6) and tighten the 8 screws (KA3*8)
(1) around the rim.
9 Installing the fan

9.1 Selecting the mounting location

10
Install the fan on a flat, solid, and stable wall that is strong enough to support the weight
of the fan.
Install the fan in a safe location on the wall. Do not install the fan directly above a bed, cot,
11
or similar location to avoid accidental hazards.
The fan must be installed at least 210 cm above the floor.
9.2 Mounting the fan
When penetrating the surface (example: drilling or inserting fasteners), make sure
no cables or pipes are damaged. Inadvertently penetrating electric cables causes
the life-threatening danger of an electric shock! Check for concealed wires and
pipes before drilling or inserting fasteners.
40mm
Min. 210 cm
Fig. 1
PRECONDITIONS:
A
You have the following tools at hand: cross-head screwdriver, drill and suitable drill bit,
D
B
hammer and pencil.
You have mounting material that is suitable for the wall type.
D
1. Unplug the product from the mains socket.
2. Mark the mounting holes on the wall (Fig. 1).
3. Drill the holes at the marked positions about 30 mm deep. The drill bit should be the same
diameter as the expansion anchor if you are drilling into a plasterboard or concrete wall, or
smaller than the diameter of the screw if you are drilling into a wood wall.
4. If the wall is plasterboard or concrete, push the 2 expansion anchors (included) into the
holes and use a hammer to carefully tap the anchors until they are flush with the wall
(Fig. 2).
5. Screw the 2 mounting screws (included) into the holes, leaving the screw heads 2 mm
outside the wall to hang the fan (Fig. 2).
6. Insert the 2 mounting holes (9) on the fan over the screw heads and slide the fan down until
it hangs securely in place (Fig. 3). Tighten the mounting screws if required.
10 Operation
10.1 Turning the fan on/off
PRECONDITIONS:
Fan is fully assembled and securely installed on the wall.
D
1. Plug the product into a suitable mains socket.
NOTICE: Do not adjust the vertical tilt when the fan is on to avoid product damage.
2. Push the fan head up or down to adjust the vertical tilt.
3. Press the On/Off button (a, A) to turn the fan on.
4. Press the Speed button (b, B) to select the desired speed (LOW / MEDIUM / HIGH).
The corresponding speed indicator light will illuminate on the control panel.
Æ
5. To turn off the fan, press the On/Off button (a, A).
6. Unplug the fan from the mains socket if it is not going to be used for a long period of time.
10.2 Setting the oscillation
1. To turn the left-right oscillation function on or off, press the Oscillation button (c, D).
The oscillation indicator light will turn on when the function is on.
Æ
2mm
Fig. 2 Fig. 3