Selecting The Mounting Location - Sygonix 2618632 Bedienungsanleitung

6 Product overview
6.1 Fan
1
1 Safety screw 6 Back grille
2 Front grille 7 Motor shaft
3 Blade cap 8 Motor housing
4 Fan blades 9 Mounting holes
5 Back grille nut 10 Adjustable tilt neck
6.2 Remote control and control panel
e
d
c
b
a
Remote control
a. Off button
b. On/Speed button
c. Timer button
d. Mode button
e. Oscillation button
7 Installing the batteries in the remote control
1. Open the battery compartment cover on the back of the remote control.
2. Insert the new batteries (2x 1.5 V AAA batteries, not included), following the + and - ends
indicated inside the compartment.
3. Close the battery compartment cover.
8 Assembling the fan
1. Unplug the product from the mains socket.
2. Hold the back grille (6) with the handle at the top and facing backwards. Insert the back
grille onto the motor shaft (7), making sure that it is properly aligned with the front of the
motor housing (8).
3. Secure the back grille with the nut (5) by turning it clockwise.
4. Align the centre of the fan blades (4) with the motor shaft (7), and push it in.
5. Tighten the blade cap (3) on the motor shaft (7) by turning the cap anti-clockwise. Turn
the fan blades (4) a few turns with your hands to check that they are properly aligned and
turning smoothly.
8
7
5
4
3
12
2
11 Control panel and
indicator lights
12 Remote control
A
E
Control panel
A. Off button
B. On/Speed button
C. Timer button
D. Mode button
E. Oscillation button
6. Open the clips around the rim of the front grille (2) and hook the bracket at the top onto
the back grille (6).
7. Align the hole in the bottom of the grilles and close the clips to attach the grilles.
8. Secure the grilles with the safety screw (1) in the bottom using a screwdriver.
9
9 Installing the fan
10

9.1 Selecting the mounting location

Install the fan on a flat, solid, and stable wall that is strong enough to support the weight
11
of the fan.
Install the fan in a safe location on the wall. Do not install the fan directly above a bed, cot,
or similar location to avoid accidental hazards.
6 The fan must be installed at least 210 cm above the floor.
9.2 Mounting the fan
When penetrating the surface (example: drilling or inserting fasteners), make sure
no cables or pipes are damaged. Inadvertently penetrating electric cables causes
the life-threatening danger of an electric shock! Check for concealed wires and
pipes before drilling or inserting fasteners.
20 mm
Min. 210 cm
Fig. 1
PRECONDITIONS:
You have the following tools at hand: cross-head screwdriver, drill and suitable drill bit,
D
hammer and pencil.
You have mounting material that is suitable for the wall type.
D
1. Unplug the product from the mains socket.
2. Mark the mounting holes on the wall. (Fig. 1)
3. Drill the holes at the marked positions 40 mm deep. The drill bit should be the same
diameter as the expansion anchor if you are drilling into a plasterboard or concrete wall, or
smaller than the diameter of the screw if you are drilling into a wood wall.
4. If the wall is plasterboard or concrete, push the 2 expansion anchors (included) into the
holes and use a hammer to carefully tap the anchors until they are flush with the wall
(Fig. 2).
B
5. Screw the 2 mounting screws (included) into the holes, leaving the screw heads 2 mm
C
outside the wall to hang the fan (Fig. 2).
6. Insert the 2 mounting holes (9) on the fan over the screw heads and slide the fan down until
D
it hangs securely in place (Fig. 3). Tighten the mounting screws if required.
10 Operation
10.1 Turning the fan on/off
PRECONDITIONS:
Fan is fully assembled and securely installed on the wall.
D
1. Plug the product into a suitable mains socket.
The Power indicator light will illuminate on the control panel (11) to indicate that the fan
Æ
is connected to the power supply.
NOTICE: Do not adjust the vertical tilt when the fan is on to avoid product damage.
2. Push the fan head up or down to adjust the vertical tilt.
3. Press the On/Speed button (b, B) to turn the fan on.
4. Press the On/Speed button (b, B) to select the desired speed (LOW / MEDIUM / HIGH).
The corresponding speed indicator light will illuminate on the control panel.
Æ
5. To turn off the fan, press the Off button (a, A).
The fan will turn off and the Power indicator light will remain illuminated.
Æ
6. Unplug the fan from the mains socket if it is not going to be used for a long period of time.
10.2 Setting the oscillation
To turn the left-right oscillation function on or off, press the Oscillation button (e, E).
The fan head will start to oscillate from side to side when the function is on.
Æ
Fig. 2 Fig. 3