Sharp Party Street Beat PS-949 Bedienungsanleitung Seite 8

7
on the second unit will begin the process again but the second unit will be
the LEFT CHANNEL.
ū If two speakers have already been paired, Duo Mode / TWS will reconnect
automatically when both speakers are powered on.
ū When in Duo Mode, only the Bluetooth from the LEFT CHANNEL will
be shared. Input from Mic 1 and Mic 2 on both speakers will remain local
to that speaker.
ū AUX is not available on the RIGHT CHANNEL
ū Controls shared between speakers in Duo Mode are:
Volume control
Play and Skipping
Disco Lights
Strobe Lights
EQ
Super Bass
Power ON/OFF
ū To disconnect from another speaker in Duo Mode / TWS, press and
hold the TWS Button. This will disconnect the paired speaker and also
the paired Bluetooth Device. Press and hold the TWS button again to
reconnect all devices.
ū The maximum distance between two speakers is 10 metres.
AUX mode
The XParty Street Beat can be used to listen to audio from external
devices.
1. Connect an auxiliary audio device to the unit via the 3.5mm Audio
lnput.
2. Press the button until the LCD display shows <AUX>.
3. Play and control music on the source audio device.
NOTES:
ū In Duo Mode, only the LEFT CHANNEL speaker can be connected to via
your AUX device for playback.
ū Audio played on the left channel will not play on the right channel whilst
in Duo Mode.
Mic/Guitar operation
The XParty Street Beat can support two microphones, guitars or other
6.3mm TRS audio inputs.
WARNING:
• Before connecting a device to Mic 1 or Mic 2, ensure the volume on
the XParty Street Beat is low.
• This will avoid any sudden feedback or loud noise from the speaker
when, for example, turning on the microphone or if the volume on the
guitar is set to high.
• Whilst using microphones, ensure there is adequate distance between
the microphones and the speaker to avoid feedback.
Using a microphone, guitar or other audio input
1. Plug the 6.3 mm jack into the Mic 1 or 2 socket. If you have another
device, insert this into the remaining socket.
2. To control the speakers output volume of the devices, press the
corresponding or
the Control Knob to adjust the volume until you reach the desired
output level.
Reverb
You can add a reverb effect to devices connected to Mic 1 or Mic 2 inputs
and adjust how much of the effect is applied.
1. To turn reverb on for Mic 1, short press (<1 second) the reverb
button. The icon will flash on the LCD display.
2. Turn the Control Knob to adjust the reverb level from <RB000> to
<RB100>.
3. To turn reverb on for both Mic 1 and Mic 2 inputs, short press (<1
second) the reverb button 2 times in a row. The
will flash on the LCD display.
4. To turn reverb off, long press (>2 seconds) the reverb button.
button on the control panel and rotate
and
NOTES:
ū The reverb effect is only applied to the Mic inputs and is set at 50% as
default.
ū If the reverb level % value was changed and then reverb turned off, the
value will be saved.
ū If reverb is turned on for both Mic 1 and 2, the level of effect is the same
for both inputs.
USB mode and charging functions
(Refer to 3 ,
The speaker can support USB playback and charging.
USB playback
1. Insert the USB device into USB input that has the
2. Press the
across the LCD display.
3. The stored music will start playing. You can use the
buttons to control playback.
USB charging
1. Mobile devices can be charged via the USB charging port (5V, 1A).
NOTES:
ū All compatible audio files will play automatically.
ū Files are played in order based on their folder locations and in alpha-
numeric order.
ū If you want to play files in a specific order, ensure your files are in the root
folder. Make sure the file name begins with the number in the order you
want the files to play in.
ū The maximum USB flash disk size is 128GB. Disks greater in capacity will
not work.
ū When playing back audio via USB, ensure you connect your USB device to
the USB input that has the
ū When charging a device, ensure you connect the device to the USB
Charging port (5V, 1A).
ū In Duo Mode, only the LEFT CHANNEL speaker can be connected to your
USB device for playback.
ū Audio played on the left channel will not play on the right channel whilst
in Duo Mode.
EQ, Super Bass, Disco lights and DJ FX
Adjust the EQ
You can adjust the EQ of the speaker with pre-loaded equalizer settings
for popular music types.
1. Press the EQ button repeatedly to select the EQ effect:
POP, DANCE, ROCK, LIVE, CLUB and FLAT.
The LCD display will show the selected EQ.
NOTES:
ū In Duo Mode You can adjust the EQ using the EQ button on either the LEFT
or RIGHT unit.
ū To get the best results and if available, make sure your source device has
the EQ set to "flat" or "off". Not all devices have EQ.
Super Bass
You can enhance the bass performance with the Super Bass function.
Press the SUPER BASS button to turn on, <BASS ON> will be displayed
on the LCD display.
To turn off, press SUPER BASS again, <BASS OFF> will be displayed on
the LCD display.
Disco lights
icons
You can adjust the light effect of the speaker unit.
1. Press the
ROLLERZ, GLOW, INFINITY, BLINK, CLUB, PRISM and LIGHTS OUT. The
4 on page 1).
button to switch to the USB mode. <USB> will scroll
symbol.
button repeatedly to select the light effect:
symbol.
and