Light Function On/Off; Operating 6 Cars; Encoding/Programming Of Autonomous Car; Encoding/Programming Pace Car - Carrera DIGITAL 132 Montage- Und Betriebsanleitung

Light function on/off
3 sec.
4
STOP
5
The car programmed to the speed controller will have to come to a
stop for at least 3 seconds before the light can be switched on or off
by the push of the lane-change-button.
Note:
applies only to models fi tted with lighting

Operating 6 cars

Plug speed controller extension set (item no. 20030348) in connec-
tor 1 of the Control Unit. For next steps see section "Coding of cars
to the according speed controller".
Encoding/programming
of Autonomous Car
2 1
1 2
7 2x 8
3 4
5
150
SPEED
100 200
+
CLICK
50 250
0 300
Switch on the Control Unit, place the car to be encoded on the track
and press „Code" 8 twice, fi g. . The fi rst two LEDs at the Con-
1
trol Unit start to light, fi g. 2 . Now push the lane-change button at
the speed controller, fi g. ; LEDs 3-5 will light successively. Wait
3
until the middle LED lights again, fi g.
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, fi g. .
5
Autonomous Car´s encoding is completed now.
Note: This kind of encoding requires having only the car on the
track which is to be encoded. The programming of the Autono-
mous Car will be maintained unless the car is not being recoded.
The Autonomous Car is always displayed with address 7 in combi-
nation with the Position Tower.
Encoding/programming
Pit Lane 20030356
3 2
1
6 7 3x 8
3
5
150
200
100
50 250
0 300
(only in combination with Pit Stop Lane #20030356)
Switch on the Control Unit, place the car to be encoded on the track
and press "Code"
the Control Unit start to light, fi g.
ton at the speed controller, fi g.
Wait until the middle LED lights again, fi g.
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, fi g.
completed now and the car enters the Pit Stop Lane.
Note: This kind of encoding requires having only the car on the
track which is to be encoded. The programming of the Pace Car
will be maintained unless the car is not being recoded. The Pace
Car is always displayed with address 8 in combination with the Posi-
tion Tower.
Extended Pace Car function
After the Pace Car´s encoding has been completed it will auto-
matically enter the Pit Lane during the fi rst laps. In order to start the
Pace Car please push the button "Pace Car"
2 and 3 at the Control Unit will light and the Pace Car will leave the
Pit Lane. The Pace Car will now drive as long as the button „Pace
Car" is pushed again. LED 2 stops lighting and the car automatically
enters the Pit Lane within the current lap.
. Activate the speed
4
Pace Car
1
2
4 3
4
5 6 7
SPEED
+
CLICK
5
8 three times, fi g. . The fi rst three LEDs at
1
2 . Now push the lane-change but-
; LEDs 2-5 will light successively.
3
. Activate the speed
4
. The Pace Car´s encoding is
5
4 once. The LEDs
4 3
5 6 7
5
Setting of the
cars´ basic speed
1 1 – 10 2
3 4
2 1
5 6
8
4 3 2
The setting of the basic speed can be eff ected individually for one
and/or several cars. The cars which are to be adjusted have to be
6 7
positioned on the track. The setting can be carried out on 10 levels
with the 5 LEDs indicating the diff erent levels by fl ashing or perma-
nent lighting.
1 LED lights = low speed
1
5 LEDs light = high speed
2
Switch on the Control Unit, place the cars to be adjusted on the
track and press "SPEED" 5 once. A certain number of LEDs will
now light, showing the speed level last used. Push the "SPEED"
button 5 as many times until you have reached the speed desired.
3
Confi rm by pressing "ENTER/START" . A short running light and
the lighting of the middle LED confi rms completion of the setting,
fi g. .
6
Setting of cars´
braking performance
1 – 10
1 2
3 4
2 1 5
5 6
8
4 3 2
(only for cars operated with speed controllers)
The setting of the braking performance can be eff ected individually
6 7
for one and/or several cars. The cars which are to be adjusted have
to be positioned on the track. The setting can be carried out on 10
levels with the 5 LEDs indicating the diff erent levels by fl ashing or
permanent lighting.
1 LED lights = low braking eff ect
1
5 LEDs light = high braking eff ect
2
Switch on the Control Unit, place the cars to be adjusted on the
track and press "BRAKE" 6 once. A certain number of LEDs will
now light, showing the brake step last used. Push the "BRAKE" but-
ton 6 as many times until you have reached the braking perfor-
mance desired. Confi rm by pressing "ENTER/START"
running light and the lighting of the middle LED confi rms completion
of the setting, fi g. 6 .
1 – 10
3
5 6
1
8
1 – 10
3
2
6 7
1
8
3 . A short
11