Setting Fuel Tank Capacity; Deactivating Settings Keys; Extended Pit Lane Function; Sound On/Off - Carrera DIGITAL 132 Montage- Und Betriebsanleitung
Teil b
Vorschau ausblenden
Andere Handbücher für DIGITAL 132:
- Bedienungsanleitung (155 Seiten) ,
- Montage- und betriebsanleitung (53 Seiten) ,
- Kurzanleitung (2 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Setting fuel tank capacity
1 – 10
1
3
3
5
6
3
2
5
6
7
8
4
3
(only for cars operated with speed controllers)
The setting of the fuel tank capacity in combination with the Pit Lane
5
6
(20030356) is eff ected for all cars simultaneously. The setting can
be carried out on 10 levels with the 5 LEDs indicating the diff erent
levels by fl ashing or permanent lighting.
1 LED lights = low fuel capacity
1
5 LEDs light = full tank
2
Switch on the Control Unit, place the cars to be adjusted on the
track and activate the fuelling function by means of the slide switch
2
, fi g.
. Press the "FUEL" button
3
LEDs will now light, showing the fuel capacity last used. Push the
"FUEL" button
7
as many times until you have reached the fuel
capacity desired. Confi rm by pressing "ENTER/START"
running light and the lighting of the middle LED confi rms completion
of the setting, fi g
.
6
4
Extended fuelling function
You can choose between 3 modes via the sliding switch
fi g.
:
3
• OFF = cars don´t consume any "petrol"
• ON = cars consume "petrol"
5
• REAL = maximum speed depending on fuel tank capacity / cars
consume "petrol") (only in combination with Pit Lane 20030356 or
Pit Stop Lane 20030346 and Pit Stop Adapter Unit 20030361)
4
When driving in "REAL-mode" the car with a full tank is "heavier",
drives slowlier and shows a lower braking eff ect; a car with an empty
tank is "lighter", drives faster and shows a higher braking eff ect. The
current fuel tank capacity and the "fuel consumption" can only be
5
displayed in combination with the Driver Display 20030353 and Pit
Stop 20030356.
Refuelling of cars with Pit Lane 20030356
and Driver Display 20030353
7
Pit Lane 20030356
Driver Display 20030353
4
9
10
5
4
The car´s present tank capacity can be read via the bar display with
5 green and 2 red LEDs at the Driver Display. For refuelling drive
your car into the Pit Lane across the refuelling sensor fi g.
5
bar display now starts to fl ash, fi g.
8
by keeping the lane-change button pushed. fi g.
refuellings are indicated by fl ashing or lighting of the yellow LEDs,
fi g.
(also see Driver Display).
10
Note: cars with an empty tank are disregarded for lap-counting
in combination with Position Tower 20030357.
12
Setting of tank capacity at the start of the race
Pit Lane 20030356
1 – 10
2
11
2
1
4
4
7
8
1
13
5
6
2
1
(only in combination with Pit Lane 20030356 and Driver Display
20030353) Irrespective of the basic setting of the tank capacity it is
possible to individually set the tank capacity for one or several cars
at the race´s start for the number of laps till the fi rst pit stop. Push
7
8
"START/ENTER" once
permanently, fi g.
fi g.
. Clicking the lane-change button at the corresponding speed
13
controller enables you to change the fi ll level, fi g.
Deactivating Settings Keys
7
once. A certain number of
4
3
1
3
. A short
5
6
3
2
2
,
3
6
7
8
3
2
To deactivate the keys for setting Speed, Brake and Fuel, proceed
as follows: Hold down the Code Key
6
7
8
While holding down the Code Key
then release the Code Key. To reactivate the above keys, repeat the
procedure just described.
Extended Pit Lane function
8
Pit Lane 20030356
1
3
2
3
6
7
8
3
2
5
. The
7
6
7
8
, and the car can be refuelled
. The number of
9
(only in combination with Pit Lane 20030356)
Driver Display 20030353
12
3
2
14
6
7
8
4
3
5
6
7
3
; the 5 LEDs at the Control Unit will light
12
, and the Driver Display´s bar display will fl ash,
4
3
.
14
5
6
7
2
7
8
1
4
3
1
5
6
7
8
.
8
, turn on the Control Unit and
4
3
5
6
7
2
1
5
4
1
5
6
4
3
5
6
It is possible to activate/deactivate the lap counting function in the Pit
Lane 20030356 or Pit Stop Lane 20030346 with the Pit Stop Adapter
Unit 20030361. Switch off the Control Unit, keep "SPEED" button
pushed, switch on Control Unit and release "SPEED" button
By pushing the button again, 1 or 2 LEDs will light depending on
the setting.
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, fi g.
. The settings will now be adopted. Push
5
"START/ENTER"
3
for leaving the settings again.
1
Sound ON/OFF
1
2
2
1
4
3
8
5
2
1
The confi rmation sound when crossing the sensors and the key
sound can be switched off . Switch off the Control Unit and keep the
8
"START/ENTER" button
3
pushed, switch on the racetrack and
release "START/ENTER"
3
again. The acknowledgement sound
for switching on the Control Unit cannot be switched off however.
Reset function
1
2
2
1
3
8
2
1
To restore the Control Unit to factory settings the Control Unit off ers
a reset function.
8
Switch off the Control Unit and keep the "ESC/PACE CAR"
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaff ected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
3
2
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
6
7
Energy-saving mode
3
2
After 20 minutes of non-usage the Control Unit switches to ener-
gy-saving mode and all displays such as Position Tower, Driver
6
7
Displays and Startlight are turned off . To reactivate the controller,
switch it off for 2 or 3 seconds, then switch it on again. All settings
will be kept.
2
1
7
8
5
)
5
.
3
2
6
7
4
3
5
6
4
but-
1
8
1
8
Werbung
Inhaltsverzeichnis
