Specifications; Additional Safety Rules For Tool; Functional Description - Makita TW1000 Betriebsanleitung

ENGLISH
1 Switch trigger
2 Side grip
3 Groove
4 Socket
5 Anvil

SPECIFICATIONS

Model
Capacities
Standard bolt .............................................. M24 – M30
High tensile bolt .......................................... M22 – M24
Square drive ...................................................... 25.4 mm
–1
No load speed (min ) ............................................ 1,400
Impacts per minute ................................................. 1,500
Max. fastening torque ..................................... 1,000 N•m
Overall length ..................................................... 382 mm
Net weight .............................................................. 8.4 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for fastening bolts and nuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety Hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES FOR TOOL

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to impact wrench safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will also make exposed
metal parts of the tool "live" and shock the oper-
ator.
2. Wear ear protectors.
3. Check the socket carefully for wear, cracks or
damage before installation.
4. Hold the tool firmly.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6. The proper fastening torque may differ depend-
ing upon the kind or size of the bolt. Check the
torque with a torque wrench.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
6 O-ring
7 Pin
8 High tensile bolt
9 Fastening torque
10 Fastening time
WARNING:
MISUSE or failure to follow the safety rules stated in
TW1000
this instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
/II
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
• Change the direction of rotation only when the tool
comes to a complete stop. Changing it before the tool
stops may damage the tool.
The switch is reversible, providing either clockwise or
counterclockwise rotation. To start the tool, simply pull
the lower part (A) of the switch trigger for clockwise, or
the upper part (B) for counterclockwise. Release the
switch trigger to stop.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing side grip (auxiliary handle) (Fig. 2)
GEB009-1
Fit the side grip into the groove on the hammer case and
fasten securely. The grooves for the side grip installation
are located in two positions. Install it at the proper posi-
tion according to your work.
Selecting correct socket
Always use the correct size socket for bolts and nuts. An
incorrect size socket will result in inaccurate and incon-
sistent fastening torque and/or damage to the bolt or nut.
Installing or removing socket
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the socket.
For socket without O-ring and pin (Fig. 3)
To install the socket, push it onto the anvil of the tool until
it locks into place.
To remove the socket, simply pull it off.
11 Limit mark
12 Protector
13 Brush holder cap
14 Screwdriver