Battery Status - Kress KG347E Serie Bedienungsanleitung

simple push and slight pressure will be sufficient until
a click is heard. Check to see if the battery is fully
secured.
NOTE:
• When removing the battery pack, hold it firmly
to avoid dropping and injury.
• This machine will only run when 2 batteries are
installed. It is recommended to use the same
two batteries and charge the two batteries at
the same time.
• When you use two batteries with different
power, the machine will only run to the lower
common denominator.
5. POWER INDICATOR LIGHT (See Fig. J)
IMPORTANT:
When only one light is illuminated, your battery is
overly discharged, even though the machine may
still be capable to work. Continuing to operate
your machine with the battery in this discharged
condition may reduce the life and performance of
your battery.
When no light are illuminated, at least one battery
is not fully installed or battery may be defective,
please double check the batteries are fully seated
into position.

BATTERY STATUS

• Before starting or after use, press the button
16
beside the power indicator light on the machine to
check the battery capacity.
EN
• During operation, the battery capacity will be
indicated automatically by the battery power
indicator. The indicator constantly senses and
displays the battery condition as follows.
• For the machine with 2 battery packs with
different power, the power indicator light displays
the battery condition with the lower one of the two
batteries.
Battery indicator
light status
Five green lights
( ) are
illuminated.
Two, three or four
green lights are
illuminated.
Only one green
light ( )
is illuminated.
No light is
illuminated.
Battery condition
The two batteries are in a
highly charged condition.
The two batteries have a
remaining charge. The more
lights are illuminated, the
more battery capacity.
The battery level of at least
one battery pack is very low.
Please check and charge the
battery pack.
At least one battery is not fully
installed or battery may be
defective.
Only one light is At least one battery is over
flashing twice per discharged (please refer to
cycle. the battery charge condition),
please recharge the two
batteries at once before use
again or storage.
Only one light At least one battery is hot,
is flashing three wait for them cool down
times per cycle. before start again.
Only one light is The machine is over load.
flashing four times Remove tool from cutting
per cycle. area and try again.
6. SWITCHING ON AND OFF (SEE FIG. K)
ATTENTION: Check the battery packs before
using your cordless tool. Only use the battery
pack listed in the accessories section.
For switching on the tool, press the lock-out button,
then fully press the on/off switch and hold in this
position. The lock-out button can now be released.
For switching off, release the on/off switch.
NOTE: The chain brake must be activated in order for
the saw to be switched on.
7. CHAIN BRAKE LEVER (See Fig. L)
The chain brake lever is a safety mechanism
activated through the front hand guard, when
kickback occurs. Chain stops immediately.
The following function check should be carried out
at regular intervals. Pull the front hand guard towards
the operator (position
To activate the chain brake, push front hand guard
forwards (position ).
NOTE: If the saw is unable to start, even though it is
assembled properly and working with fully charged
battery packs, then you should check if the chain
brake lever is in the correct position (position
8. CUTTING
IMPORTANT: Is the oil tank filled? Check
the Oil Level Window prior to starting and
regularly during operation (See Fig. M). Refill oil
when oil level is low. A full oil tank will last approx.
12 minutes of cutting depending on sawing
intensity and stops.
Check recent replaced chain tension about every
10 minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying on
the ground. This will keep the chain from touching
the ground as it cuts through the log.
Touching the ground while the chain is moving is
dangerous and will dull the chain.
(3) Use both hands to grip saw. Always use left hand
to grip front handle and right hand to grip rear
handle. Use a firm grip. Thumbs and fingers must
wrap around saw handles. (See Fig. N)
(4) Make sure your footing is firm. Keep feet-shoulder
width apart. Distribute your weight evenly on both
) to deactivate chain brake.
).