Vibration Information; Assembly - Kress KG347E Serie Bedienungsanleitung

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined
according to EN 62841:
Vibration emission value
a = 4.8 m/s
2
h
The declared vibration total value and the declared
noise emission value have been measured in
accordance with a standard test method and may be
used for comparing one tool with another.
The declared vibration total value and the declared
noise emission value may also be used in a
preliminary assessment of exposure.
WARNING: The vibration and noise emissions
during actual use of the power tool can differ
from the declared value depending on the ways
in which the tool is used especially what kind of
workpiece is processed dependant on the following
examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well maintained.
The use of the correct accessory for the tool and
ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration and noise accessories are used.
14
And the tool is being used as intended by its design
and these instructions.
EN
This tool may cause hand-arm vibration syndrome
if its use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration and noise
exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
Uncertainty K = 1.5m/s²

ASSEMBLY

WARNING! Do not install the battery pack
before it has been completely assembled.
Always use gloves when handling the chain.
CHAIN AND GUIDE BAR ASSEMBLY
1. Unpack all parts carefully. Remove the chain cover
by turning the chain tensioning knob in a counter-
clockwise direction. (See Fig. A1)
2. Place the Chainsaw on a solid, level surface.
3. Use only genuine Kress chains or those
recommended for Guide Bar.
4. Slide the chain in the slot around the guide bar.
Ensure the chain is in correct running direction by
comparing it to the chain icon on the guide bar, or
referring to the chain direction symbol found on
the saw body. Ensure the bar tensioning plate is
facing outward. (See Fig. A2)
5. Fit the chain onto the drive sprocket, so that the
fastening bar bolt and the two bar locating tabs on
the bar pad fit into the keyway of the opening on
the guide bar. (See Fig. B1, B2)
6. Assure all parts are seated properly and hold
chain and guide bar in a level position. Make sure
the drive links are fully seated in the drive sprocket
(See Fig. C1), avoiding a kink as shown in Fig. C2.
If kink occurs, pick up on the chain at the guide
bar just ahead of the kink and then pull the kink
out.
NOTE: Chain should rotate freely and be free of
kinks.
7. Fit the chain cover and tighten the chain cover by
turning the chain tensioning knob clockwise until it
is tight. (See Fig. D)
8. The chain will stretch while cutting and lose
proper tension. When the chain becomes loose,
completely unscrew the chain tensioning knob
or turn the knob around three (3) full turns in a
counter-clockwise direction, then retighten the
chain tensioning knob to properly reset the chain
tension by repeating Steps 6-7 listed above.
WARNING: The chain is not yet tensioned.
Tensioning the chain applies as described
under "TENSIONING CHAIN". The chain
now needs to be inspected to make sure it is
properly tensioned.
TENSIONING CHAIN (See Fig. E1, E2)
NOTE: New saw chains will stretch. Check the chain
tension frequently when first used and tighten when
the chain becomes loose around the guide bar.
WARNING:
● Removing the battery pack before adjusting saw
chain tension.
● Cutting edges on chain are sharp. Use protective
gloves when handling chain.
● Maintain proper chain tension always. A loose
chain will increase the risk of kickback. A loose
chain may jump out of guide bar groove. This may
injure operator and damage chain. A loose chain