Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch WEU Uneo Maxx Originalbetriebsanleitung

OBJ_BUCH-1190-003.book Page 15 Tuesday, May 28, 2013 9:42 AM
Battery Charge-control Indication
The battery charge-control indicator 9 consists of three green
LEDs, and indicates the charge condition of the battery for a
few seconds when the On/Off switch 8 is pressed halfway or
fully.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slow flashing 1 x green
The 3 LEDs of the battery charge-control indicator 9 and the
Power Light 11 flash rapidly when the battery temperature is
not within the operating temperature range of –30 to +65°C.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature of 65 °C is exceeded, the electronic control
switches off the power tool until the temperature is in the op-
timum temperature range again.
The 3 LEDs of the battery charge-control indicator 9 and the
"Power light" 11 flash rapidly when the battery temperature is
not within the operating temperature range of –30 to +65°C
and/or when the overload protection has actuated.
Protection Against Deep Discharging
The Lithium-Ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.

Working Advice

 Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.

Maintenance and Service

Maintenance and Cleaning

 For safe and proper working, always keep the machine
and ventilation slots clean.
 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Bosch Power Tools
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
Capacity
concerning our products and their accessories.
≥ 67%
Great Britain
34—66% Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
11—33%
Broadwater Park
≤ 10%
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
English | 15
1 609 92A 09P | (28.5.13)