Getting Started/Operation - Sygonix 2525291 Bedienungsanleitung

Attach the bracket securely to the door and tighten the two screws.
Connect the camera cable to the back
of the display. Ensure the plug is cor-
rectly aligned. See the picture on the
right.
Finally, hang the display on the brack-
et. Ensure the camera cable is not
pinched.
The installation is now complete.

8 Getting started/operation

8.1 Functions of the sliding switch/reset button/status LEDs of the indoor unit
Sliding switch/but- Action
ton/LED
Sliding switch (L) "ON"/"OFF"
Home button (H) press briefly
"RESET" button (J) keep pressed for
approx. 3 seconds
LED (H) flashes blue
LED (H) flashes alternately
red and blue
LED (H) flashes blue once
LED (K) glows red steadily
8.2 Charging the indoor unit/display
To be able to use the product, you must first charge the battery.
Connect the included micro USB cable to the display's micro USB port (K).
Once the micro USB port is energised, the LED integrated into the micro USB port goes on
and glows red steadily. When the battery is fully charged, the battery symbol appears in the
app and on the display of the indoor unit.
The product battery can also be charged during operation.
8.3 Inserting the memory card
If you want to use a memory card, insert it into the card slot. The display must be switched
off while doing so. The sliding switch (L) must be in the "OFF" position.
Slide the memory card into the slot and push it in until it clicks into place. When inserting
the card, its contacts must face the back of the display.
If you want to remove the memory card, push the card in again to eject it. Then pull it out
of the slot.
8.4 Product functions
To switch the product on, slide the switch (L) from the "OFF" position to the "ON" position.
During camera initiation, the red and blue LEDs glow steadily.
To switch the product off, slide the switch from the "ON" position to the "OFF" position.
To make a call, the visitor must simply press the call button (G) briefly.
Press the home button (H) briefly to turn the display on.
To turn the display off, simply press the home button (H) again briefly. The display is deac-
tivated automatically after a few seconds.
Function
Switches the system on or off
Switches the display on or off
Resets the system to factory defaults; after
initiation, the connection mode is enabled
automatically
The indoor unit is in connection mode
The indoor unit is connected to the app
The call button on the door viewer has been
pressed
The indoor unit is powered via the micro USB
port
9 Configuring and using the app
9.1 Installing the app
Open the respective app store on your smartphone. If you are using
Android , open "Google Play". If you are using an Apple device, open
TM
"App Store" from Apple.
Search for the "Smart Life - Smart Living" app (house icon with blue
background) and install it.
You can also scan the respective QR code below or tap on the name. You will be redirected
to the page of the appropriate store.
Google Play
9.2 Launching the app for the first time
Open the previously installed "Smart Life - Smart Living" app.
If you have not created a free account yet, please sign up and follow the instructions.
Log in to the app using your account.
If you are using several devices, we recommended that you create a profile for your home
first. You can then create several profiles (e.g. for each room). The corresponding settings
page in the app can be accessed with the button in the lower right corner.
9.3 Configuring the product
For configuration, your smartphone and door viewer should be connected to the same
Wi-Fi network.
Important: Please note that only 2.4 GHz Wi-Fi networks are supported.
Before connecting your door intercom to the app, ensure the connection mode is enabled.
Switch on the door intercom. Wait until a camera image appears on the display.
Keep the "RESET" (J) pressed for approx. 3 seconds using a pointed object until you hear
the "System Reset" voice alert. Then release the button.
You will also hear alerts at certain intervals that the device is ready to be connected to the
app. The home button LED now flashes blue. The display switches off automatically after
approx. 5 minutes. Switch the display off and on again briefly, then the connection mode
is active again.
You can add a new device manually by tap-
ping "+" on the top right of the app's main
page and selecting the device you want to
add. Otherwise, tap the blue button below in
the middle.
You can add the door intercom to the app by
selecting the eighth item for video monitoring
in the left column (see the left black rectangle
in the screenshot).
Then select "Smart Doorbell" (see the right
black rectangle in the screenshot).
Tapping this rectangle takes you to the next
configuration page.
If the display is still on and the blue LED is still
flashing, check the box (small rectangle in the
screenshot) for the button below to turn blue
and get activated.
Then tap the bottom blue button in the app to
go to the Wi-Fi settings.
If your Wi-Fi network has not been applied
automatically, first select it (tap the double
arrow on the right) and then enter the Wi-Fi
password.
Tap the blue button to save your selection
and continue.
6
Apple iOS