Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
Wi-Fi door intercom with door viewer
Item no. 2525291
1 Intended use
The product is designed for access monitoring, e.g. in private living quarters. It can be used as
a door viewer or instead of your existing peephole.
Using the door viewer camera, you can see on the display of the indoor unit who is standing in
front of your door. The product can be connected to your smartphone and the app to enable an
intercom function via the built-in microphone and loudspeaker.
The door viewer also features a call button that triggers a ring signal on the indoor unit when
pressed. The call is also automatically redirected to your smartphone. An integrated IR LED,
which is automatically controlled via the built-in light sensor, enables door viewer operation in
darkness. An integrated motion detection functionality is also available.
The "Smart Life – Smart Living" app serves for configuration and enables to perform all other
functions. You cannot operate the product when not connected to the app. The app can be in-
stalled on a smartphone or tablet running on Android
to use the app. It must be created during the initial app setup. The configuration serves for
integrating the product into your existing Wi-Fi network.
The product is powered by a built-in rechargeable battery. The battery can be charged via the
micro USB port of the indoor unit.
The product is intended for indoor use only. Do not use it outdoors. Contact with moisture must
be avoided under all circumstances.
Using the product for purposes other than those described above may damage the product.
Improper product use can cause a short circuit, fire, electric shock, other hazards.
This product complies with statutory, national and European regulations. For safety and ap-
proval purposes, you must not rebuild and/or modify the product.
Read the instructions carefully and store them in a safe place. Always provide these operating
instructions when giving the product to a third party.
All company and product names contained herein are trademarks of their respective owners.
All rights reserved.
Android
is a registered trademark of Google LLC.
TM
2 Delivery content
Display/indoor unit
Door viewer/camera
Micro USB cable
3 Latest product information
Download the latest product information at
shown. Follow the instructions on the website.
4 Explanation of symbols
The following symbols appear on the product/device or in the text:
This symbol warns of hazards that can lead to personal injury. Read the information
carefully.
5 Safety information
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General information
This product is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. It may become a dangerous play-
thing for children.
Should you have any questions or concerns after reading this document, please contact
our technical support or a professional technician.
5.2 Handling
Please handle the product carefully. Impact, shocks or a fall even from a low height can
damage the product.
or Apple iOS. A free account is required
TM
Reset pin
Installation material
Operating instructions
www.conrad.com/downloads
or scan the QR code
5.3 Operating conditions
Do not expose the product to any mechanical stress.
Protect the product from extreme temperatures, strong jolts, flammable gases, vapours,
and solvents.
Protect the product from high humidity and moisture.
The product must not be exposed to direct sunlight.
Avoid operation near strong magnetic or electromagnetic fields, transmitter aerials or HF
generators. Otherwise, the product may not function properly.
5.4 Li-ion battery
The rechargeable battery is permanently built into the product and cannot be replaced.
Never damage the battery. Damaging the casing of the rechargeable battery might cause
an explosion or a fire!
Never short-circuit the contacts/connections of the rechargeable battery. Do not throw the
battery or the product into fire. There is a danger of fire and explosion!
Charge the rechargeable battery regularly, even if you are not using the product. The re-
chargeable battery is designed so that it does not need to be discharged before it can be
charged.
Never leave the product unattended during charging.
When charging, place the product on a surface that is not heat-sensitive. Normally, a cer-
tain amount of heat is generated during charging.
6 Product overview
Door viewer/camera
A Microphone for the intercom function
B Light sensor; the IR LED turns on automati-
cally when the light level is below 2 LUX
C PIR motion sensor for motion detection
D IR LED for a clearer picture in darkness
E Loudspeaker for the intercom function
F Camera
G Call button
Display/indoor unit
H Home button and status LED
I
SD card slot
J Reset button
K Micro USB port for battery charging with an
integrated status LED
L On/off switch
7 Installation
The product can serve as a door viewer on your front door. It can also be used instead of an
existing peephole.
7.1 Preparation
You should remove the existing peephole first before installing the door viewer on your
front door.
If there is no peephole on your front door, drill a hole with a diameter of 16 mm at eye level.
7.2 Installation
First, pull off the two protective strips to expose the adhesive strips.
Thread the connecting cable of the camera through the hole in your door from the outside.
Then push the camera into the hole from the outside and press it down lightly. Pay attention
to the correct orientation when doing so. The call button must point downwards.
Pick up the indoor bracket and 2 of the 6 screws included in the delivery. Select the screws
according to the thickness of your front door.
Indoor bracket alignment: The two adhesive strips must face the door. The recessed
square for the cable must point to the left and the two recesses for the screws to the right.
First, pull off the two protective strips to expose the adhesive strips.
Thread the camera cable through the recessed square of the bracket and push it into the
slot in the middle of the bracket.
Insert the screws one by one into the bracket recesses and screw them into the back of the
camera. Do not attach the bracket to the door yet.
With the screws slightly tightened, push the bracket all the way to the right so that the two
screws are in the middle of the bracket.
5
Werbung
Inhaltsverzeichnis
