Declaration Of Conformity; Mounting And Operation - Bosch Rotak 36 LI Originalbetriebsanleitung

OBJ_BUCH-1954-003.book Page 15 Monday, September 16, 2013 1:14 PM

Declaration of Conformity

We declare under our sole responsibility that the product described under "Technical data" is
in conformity with the following standards or standardization documents: EN 60335 accord-
ing to the provisions of the directives 2011/65/EU, 2004/108/EC, 2006/42/EC,
2000/14/EC.
2000/14/EC: Guaranteed sound power level
Conformity assessment procedure according to Annex VI.
Equipment category: 32
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS4,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
23.07.2013

Mounting and Operation

Action
Delivery Scope
Handle Assembly
Snap together the Grassbox
Grassbox fitting/removing
Battery Charging
Inserting the Battery
Insert Isolator Key and fit in the Storage
Position
Adjusting the Cutting Height
Starting
Working Advice
Stopping, Remove the isolator key
Removing the Battery
Blade Maintenance
Selecting Accessories
Starting
For Your Safety
 Warning! Switch off, remove the isolator key and the
battery before adjusting, cleaning or if cable is cut,
damaged or entangled.
 The blades continue to rotate for a few seconds after
the machine is switched off.
 Caution – do not touch the rotating blade.
Bosch Power Tools
Battery Charging
 Do not use other battery chargers. The supplied battery
charger is designed for the Lithium-Ion battery in your gar-
den product.
 Observe the mains voltage! The voltage of the power
supply must correspond with the data given on the name-
plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
The battery is equipped with temperature monitoring that al-
lows charging only in the temperature range between 0 °C
and 45 °C. In this manner, a high battery service life is
achieved.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Figure
The "Electronic Cell Protection (ECP)" protects the lithium ion
battery against deep discharging. When the battery is run
1
down or discharged, the garden product is shut off by means
2
of a protective circuit: The blade no longer moves.
3
4
been automatically switched off. The battery can be dam-
aged.
5
6
Charging Procedure
The charging procedure starts as soon as the mains plug of
7
the battery charger is plugged into the socket outlet and the
8
battery is inserted into the charging compartment .
9
Due to the intelligent charging method, the charging condi-
10 tion of the battery is automatically detected and the battery is
charged with the optimum charging current, depending on
11
battery temperature and voltage.
12
This gives longer life to the battery and always leaves it fully
13
charged when kept in the charger for storage.
Rapid-charging Procedure
English | 15
3 600 ... HA4 4.. HA4 5..
dB(A) 89
Do not continue to press the On/Off
switch after the garden product has
AL 3640 CV
Professional
AL 3620 CV
Professional
F 016 L70 887 | (16.9.13)
90