Activate And Deactivate The Alarm Function - TFA 30.5032 Bedienungsanleitung

TFA_No. 30.5032_Anleit_03_23
Mould RADAR thermo-hygrometer
5. For your safety
• This product is exclusively intended for the field of application described above. It should
only be used as described within these instructions.
• Unauthorized repairs, modifications or changes to the product are prohibited.
Caution!
Risk of injury:
• Keep this device and the batteries out of reach of children.
• Small parts can be swallowed by children (under three years old).
• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swal-
lowed, this can lead to serious internal burns and death within two hours. If you suspect a
battery could have been swallowed or otherwise caught in the body, seek medical help
immediately.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of
explosion!
• Low batteries should be changed as soon as possible to prevent damage caused by leak-
ing.
• Never use a combination of old and new batteries together, nor batteries of different types.
• Avoid contact with skin, eyes and mucous membranes when handling leaking batteries. In
case of contact, immediately rinse the affected areas with water and consult a doctor.
Important information on product safety!
• Do not expose the device to extreme temperatures, vibrations or shocks.
• Protect it from moisture.
6. Elements
A: Display:
A 1: 24-hour mould radar
A 2: Indoor temperature (°C/°F) and humidity / Maximum and minimum values / Dew point
A 3: Smiley for the comfort level
B: Front - Sensor buttons:
B 1: min/max button
B 2: Taupunkt (Dew point) button
C: Back - Slide switch
C 1: Alarm sound (Speaker symbol)
C 2: Animation (Arrow symbol)
12
05.03.2023 10:37 Uhr Seite 7
Mould RADAR thermo-hygrometer
D: Housing:
D 1: Suspension device
D 2: Battery compartment
D 3: Switch Taupunkt / dew point (inside the battery compartment)
D 4: Holder for the support
D 5: Warning LED when risk of mould
7. Getting started
• Remove the protective foil from the display.
• Open the battery compartment and remove the battery insulation strip.
• The device will alert you with a beep and all LCD segments will be displayed for about two
seconds.
• The indoor temperature, the humidity and the corresponding smiley symbol appear on the
display.
• The unit is ready for use.
• Attention: Do not attach the support until the settings for the animation and alarm function
are complete. The two slide switches are covered by the support.
8. Operation
8.1 Display of the 24 hours mould radar
• The device measures the relative humidity every 30 seconds and calculates from these
values every 10 minutes the average value.
• The innovative mould radar display shows graphically on a 24 hour timeline the maximum
averages that were reached.
→ The time "0h" represents the value of the current hour, "-1" the last hour "-3" of the
past 2-3 hours, "-6" of the past 4-6 hours, "-12" of the past 7 -12 hours and "-24" of
the past 13-24 hours.
→ The relative humidity values are shown in a grid of 10 from 15 to 85%. More than 65%
RH means risk of mould.
8.2 Activate and deactivate the animation
• Slide the right switch (arrow symbol) at the back forward using a pin and the automatic
animation of the 24-hour mould radar display is activated.
• On the display the black bars are flashing.
• When the animation is deactivated (switch below) the black bars appear permanently.

8.3 Activate and deactivate the alarm function

• Slide the left switch (speaker symbol) at the back forward using a pin and the alarm sound
is activated.
• If the humidity rises above 65%, an alarm sounds for a minute and a red warning light
flashes.
13