Alarm Time Setting - TFA 60.5017.01 Bedienungsanleitung

TFA_No. 60.5017_Anl_09_22
Radio controlled projection alarm clock with indoor climate
• If you select ENGLISH, the display will now appear in English.
• The sequence is shown as follows:
– Button tone (default: BEEP OFF)
– DCF reception (default: DCF ON)
– Time zone -12/+12 (default: 00)
– Hour, minutes
– Year, month, date
– Date format DATE/MONTH or MONTH/DATE (default DATE/MONTH)
6.2.1 Button tones
• Press the + or – button to activate (BEEP ON) or deactivate (BEEP OFF) the button
tone in setting mode.
6.2.2 DCF reception
• By default, the DCF reception is activated (DCF ON) and after successful reception
of the DCF signal no manual time setting is necessary.
• Press the + or – button in setting mode if you want to deactivate the DCF reception
(DCF OFF).
• The DCF reception symbol disappears.
• Once the DCF time reception is deactivated the clock must be manually set. No time
zone will appear.
• If the DCF reception is activated, the manually set time will be overwritten by the
DCF time when the signal is received successfully.
6.2.3 Setting of the time zone
• The time zone correction is needed for countries where the DCF signal can be
received but the time zone is different from the DCF time (e.g. +1=one hour plus).
• Press the + or – button to make the time zone correction (+12/-12). .
6.3 Optional display
• With the CALENDAR button you can toggle the display in normal mode:
– Weekday written in full letters
– Weekday (3 digits) with date
– Alarm time
7. Alarm clock function

7.1 Alarm time setting

• Press and hold the ALARM button for three seconds to enter the setting mode. The
alarm symbol and ALARM appear on the display.
21.09.2022 10:33 Uhr Seite 13
– 24 –
Radio controlled projection alarm clock with indoor climate
• The hour digits flash.
• Press the + or – button to set the desired time.
• Confirm the setting with the ALARM button.
• Set the minutes in the same way.
• Confirm the setting with the ALARM button.
• The current time and the alarm symbol appear on the display.
• The newly set alarm time appears in the optional display.
• The alarm is activated.
7.2 Activate and deactivate the alarm
• To deactivate and activate the alarm function, press the ALARM button in normal
mode.
• The last adjusted alarm time appears for 2 seconds on the display.
• The alarm symbol and ALARM ON appear on the display, if the alarm is activated.
• ALARM OFF appears on the display, if the alarm is deactivated.
• Wait some seconds until the display returns to normal mode to confirm the setting.
• When the alarm is activated, the alarm starts to ring when the set alarm time is
reached. The alarm symbol flashes.
• If the alarm is not stopped manually, the ascending alarm tone automatically turns
off after two minutes and it will be reactivated at the same set time on the following
day.
• When the alarm rings, press the SNOOZE/LIGHT button and the snooze function is
activated.
• The alarm will be interrupted for 10 minutes. The snooze symbol flashes on the
display.
• Press any button (except SNOOZE/LIGHT) and the alarm will stop. GOOD DAY
appears briefly on the display.
• The alarm symbol remains on the display.
8. Projection and light
Note: Continuous illuminated backlight and projection only works when using
the power adapter.
8.1 Projection
• Press and hold the Projection HIGH/LOW/OFF button for three seconds to enter the
setting mode.
• The first option flashes on the display.
• Use the + or – button to make the desired setting, while the value flashes.
• To confirm the setting, press the Projection HIGH/LOW/OFF button or wait some
seconds until the display returns to normal mode.
– 25 –