Safety Warnings - Makita DA4000LR Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Reversing switch lever
3 High
4 Low
5 Chuck key
6 Drill chuck
7 Hex wrench
8 Loosen
SPECIFICATIONS
Model
Capacities
Steel.................................................................... 13 mm
Wood ................................................................. 38 mm
–1
No load speed (min )
Angle - High....................................................... 0 – 900
Angle - Low........................................................ 0 – 400
Straight .............................................................. 0 – 600
Overall length ..................................................... 413 mm
Net weight .............................................................. 4.0 kg
Safety class ............................................................... /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
This tool is intended for drilling in wood, metal and plas-
tic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.

SAFETY WARNINGS

General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Drill safety warnings
Safety instructions for all operations
1. Use the auxiliary handle(s). Loss of control can
cause personal injury.
2. Brace the tool properly before use. This tool pro-
duces a high output torque and without properly
bracing the tool during operation, loss of control may
occur resulting in personal injury.
Explanation of general view
9 Angle housing
10 Joint
11 Socket
12 Bolt
13 Spindle
14 Two faces
15 For higher speed operation
16 Tighten
3.
DA4000LR
4.
5.
6.
7.
8.
9.
10. If the drill bit cannot be loosened even you open
ENF002-2
Safety instructions when using long drill bits
1.
GEA010-2
2.
3.
SAVE THESE INSTRUCTIONS.
WARNING:
GEB172-1
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
17 Reaction
18 Forward
19 Side grip
20 Reverse
21 Limit mark
22 Brush holder cap
23 Screwdriver
Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
Hold the tool firmly.
Keep hands away from rotating parts.
Do not leave the tool running. Operate the tool
only when hand-held.
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
the jaws, use pliers to pull it out. In such a case,
pulling out the drill bit by hand may result in injury by
its sharp edge.
Never operate at higher speed than the maxi-
mum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resulting
in personal injury.
5