Electrical Safety - Black & Decker BEW200 Bersetzt Von Den Originalanweisungen

Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Warning! Contact with or inhalation of dusts arising
u
from sanding applications may endanger the health
of the operator and possible bystanders. Wear a dust
mask specifically designed for protection against dust and
fumes and ensure that persons within or entering the work
area are also protected.
Thoroughly remove all dust after sanding.
u
Take special care when sanding paint which is pos-
u
sibly lead based or when sanding some woods and
metal which may produce toxic dust:
Do not let children or pregnant women enter the
u
work area.
Do not eat, drink or smoke in the work area.
u
Dispose of dust particles and any other debris
u
safely.
The intended use is described in this instruction
u
manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
(Original instructions)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool, along with the
date code:
a
Warning! To reduce the risk of injury, the user
must read the instruction manual.

Electrical safety

i
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Motor base
3. Random orbital sanding base
4. Large detail sanding base
5. Sanding base tip
6. Detail finger attachment
7. Dust canister
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Removing sanding bases (fig. A, B)
To remove the sanding base, undo the locking screw (9)
u
from the sanding base using the allen key (8) provided as
ENGLISH
7