Assembly And Installation - Emerson AVENTICS PE7 Montageanleitung

Function
Accelerate scroll wheel cycle
Stop scroll wheel
Save changes
1. Change menu item.
2. Save changes: Exit submenu using swipe gesture to the left or right.
ð The changes are saved automatically. Confirmation is not necessary.
Discard changes
Disconnect the product from the power supply before exiting the submenu.
u
Reset product to factory settings. See system description at
ditional documentation.
5.3.2 Versions
Material number Material designation
R412028725 PE7-PA-G014-in-V10-010-
M012
R412028726 PE7-PA-G014-ex-V10-010-
M012
R412028727 PE7-PA-G014-in-000-250-
M012
R412028728 PE7-PA-G014-ex-000-250-
M012
5.3.3 Optional: IO-Link connection
The product has an IO-Link communication interface that requires an IO-Link-ca-
pable assembly (IO-Link master) for operation. The IO-Link interface provides the
following options:
• Access to process data and diagnostic data
• Configuration of the product during commissioning and operation
• Saving parameters and transferring them to an identical product
Communication is also possible via a point-to-point connection using a USB
adapter cable and an IO-Link converter.
Input lock via IO-Link
The write protection parameter (Index 12, Subindex 0) allows the product to be
locked for inputs on the touchscreen and via IO-Link (except Index 12).
Activate input lock
Adjust the value 1 at Index 12 / Subindex 0.
u
ð The input lock on the touchscreen is active. The display shows the message
Access locked by admin.

6 Assembly and installation

Before you start with the installation: Familiarize yourself with the basic specifica-
tions for assembly as early as possible in advance. See
g 6.3 Preparation.
6.1 Notes on safety
Danger of injury due to working under pressure
When working under pressure, product parts can fly around or fluids can es-
cape under high pressure and cause serious injury or even death.
1. Before working on the product, make sure the system is without pressure
and de-energized.
2. Wear PPE.
AVENTICS™ PE7 | R412028734-BAL-001-AA | English
Operation
1 more swipe up or down
(3 speed levels)
Tap 1x on display
Description
-1 ... 1 bar, G1/4"-F, NBR,
M12-4p
-1 ... 1 bar, G1/4"-M, NBR,
M12-4p
0 ... 25 bar, G1/4"-F, NBR,
M12-4p
0 ... 25 bar, G1/4"-M, NBR,
M12-4p
g 6.2 Planning
DANGER
Danger of injury due to dangerous body currents
When working under voltage, dangerous body currents can occur and lead to
serious injuries or even death.
1. Before working on the product, make sure the system is without pressure
and de-energized.
2. Wear PPE.
6.2 Planning
6.2.1 Installation conditions
g 1.2 Ad-
General requirements
• Make sure that the product is installed in a manner that protects it from all
types of mechanical loads.
• Make sure that there is sufficient space.
Product-specific requirements
• Mounting orientation. See
• Ensure that sealing faces are clean and undamaged.
• Tightening torques depend on lubrication, seal and pressure load.
Ambient conditions
• Let the product acclimatize for a few hours before installation. Otherwise wa-
ter may condense in the housing.
• Keep the installation location free from vibration.
• Protect product from the weather.
• Protect product and housing from aggressive media.
• Protect the product from direct sunlight and UV radiation.
6.2.2 Required accessories, materials and tools
Select material and tools that are suitable for your product configuration. De-
pending on the configuration, you will need further accessories.
Mounting material
For mounting, you can use your own mounting material or AVENTICS mounting
material. Respect dimensions and tightening torques.
Tools
• No special tools required.
6.3 Preparation
6.3.1 Unpacking and checking the product
1. Check the material number to see if the product matches your order.
2. Check the product for transport and storage damage.
Do not install a damaged product. Return damaged products together with
the delivery documents. See
3. Prepare required accessories, materials and tools.
and
6.3.2 Implementing safety measures
Procedure
1. Do not carry out any work on the system during preparation.
2. Close off dangerous areas.
3. Make sure the system or system part is not under pressure or voltage.
4. Protect the system against being restarted.
5. Allow the product and adjacent system parts to cool down.
6. Wear PPE.
DANGER
g 13. Technical data.
g 4.3 Returning the product.
14