Configuration - SSS Siedle Touch 10 Produktinformation

c) In the case of telecommunica­
tion installation cable (J-Y(St)Y ...)
with a core diameter of 0.8 mm
(0.6 mm), there is a maximum
distance of 150 m (75 m) between
power supply (e.g. ANG 600-0) and
Siedle Touch ...
d) Observe the connection informa­
tion in the BTLM 651-... product
information: To operate the bus
door loudspeaker module Plus with
activated additional amplifier, an
additional supply (22–32 V DC,
e.g. NG 706-...) is required.
Installation: In-Home bus
2 Connection pcb for flush-
mounted door stations (shown with
SBTLM 651-... connection pcb)
3 Connection pcb for surface-
mounted door stations
4 In­Home bus wiring diagram
Terminal assignment
+, – Supply voltage 48 V DC
(48 V)
Da, Db Data cable Vario bus
E, G Electrically isolated input,
21–30 V DC
E (+), G (–)
6, 1 Triggering Door loud-
speaker
b, c Button illumination
12 V AC
T1, T2 Potential-free button
(system-independent, for
customer's applications,
e.g. activation of outside
light)
M1, 2 Pilfer safeguard
(if available)
LAN ext. Network connection for
configuration – LAN ext:
192.168.1.250 (upon
delivery)
Installation: Access Professional
5 Connection pcb for flush-mounted
door stations (shown with SATLM
connection pcb)
12
6 Connection pcb for surface-
mounted door stations
7 Access wiring diagram
Terminal assignment
+, – Supply voltage 48 V DC
(48 V)
Da, Db Data cable Vario bus
E, G Electrically isolated input,
21–30 V DC
E (+), G (–)
b, c Button illumination
12 V AC
T1, T2 Potential-free button
(system-independent, for
customer's applications,
e.g. activation of outside
light)
M1, 2 Pilfer safeguard
(if available)
LAN ext. Network connection for
configuration – LAN ext:
192.168.1.250 (upon
delivery)

Configuration

• The user data (such as names,
call numbers) is configured using
the configuration software on the
enclosed USB stick. For detailed
information about configuration,
see the "ST10 Configuration brief
instructions".
• The device settings (such as input
contact, network, brightness) are
configured via the network using a
web browser. Access data is required
to log into the configuration inter-
face.
Web configuration access data
(upon delivery)
User name admin
Password admin
We recommend changing the access
data after you log in for the first
time.
Keep the access data safe. Only
Siedle Engineering can reset for-
gotten access data.
Cleaning mode
Activate cleaning mode prior to
cleaning the display: Tap the top left
corner of the display six times to
activate cleaning mode (a spray
bottle appears along with a timer
that counts down to 0) and deacti-
vate the touch functions for 15 sec-
onds.
Care instructions
Clean your display carefully and only
with a soft, slightly moistened cloth.
Dry, aggressive cleaning agents and
abrasive detergents can damage the
surface!
Detailed care instructions are located
in the download area of
www.siedle.com.
Servicing
The functional unit can be com-
pletely exchanged if required.
In the event of replacement, contact
Siedle service.
Before replacement, make sure
you back up the Siedle Touch data
(e.g. button layout and configura-
tion) and transfer it to the new
Siedle Touch after replacement.
Specifications
Operating voltage: 48 V DC
Operating current: max. 500 mA
(Current consumption in idle status:
350 mA)
Protection system: IP 65 (from the
front)
Ambient temperature:
–20 °C to +55 °C
Cut-out (mm) W x H: 238 x 165
Resolution: 1280 x 800 pixels