Cameo S4 IP SNAPBAG SOFTBOX Montageanleitung

INSTALLATION INSTRUCTIONS
S4 IP SNAPBAG SOFTBOX
FOLDABLE SOFTBOX ATTACHMENT FOR S4 IP
INTRODUCTION
The softbox, for even and soft lighting, is quick and easy to mount on the spotlight.
INCLUDED
Snapbag® softbox, transport bag, diffuser cloth, mounting instructions
APPROPRIATE USE
The product is an accessory for event technology, as well as studio, TV and broadcast! This
product has been developed for professional use in the field of event technology, studio, TV and
broadcast. It is not suitable for household use! Furthermore, this product is only intended for
qualified users with specialist knowledge of event technology, as well as studio, TV and broadcast!
Use of the product outside the specified technical data and operating conditions is considered
inappropriate! Liability for damage and third-party damage to persons and property due to
inappropriate use is excluded!
SAFETY INFORMATION
1. Please read this manual carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
Use the softbox in the prescribed manner only.
5. The softbox may only be used with LED spotlights of the Cameo F series.
6. Do not leave the product unattended while in use.
Intense heat, moisture, acidic and chemically aggressive substances can
damage the product and lead to unsafe operation.
Due to its design, the softbox offers a large wind surface and is therefore
not safe in windy conditions. Only use the product when there is no wind. If
the wind starts to pick up, take the product out of operation and store it in a
wind-protected place.
The combination of the softbox with a spotlight changes the system's centre
of gravity.
This may create a risk of tipping. Do not place the spotlight unsecured on a
table edge or similar, or else be sure to use a suitable stand.
KEEP OUT OF THE REACH OF CHILDREN! THE PRODUCT CONTAINS SMALL PARTS THAT CAN BE
SWALLOWED AS WELL AS PACKAGING MATERIAL THAT CAN BE SWALLOWED! PLASTIC BAGS
MUST BE KEPT OUT OF THE REACH OF CHILDREN!
TECHNICAL DATA
Product number: CLS4IPSSBS
Product type: Spotlight accessory
Type: Softbox for Cameo Softlight S4IP
Material: Coated polyester
Colour: Black
Dimensions 905 x 620 x 270 mm
(W x H x D):
Dimensions in bag (W x 670 x 470 x 40 mm
H x D):
Weight: 1.05 kg (incl. bag)
Accessories included: Diffuser cloth, transport bag
DISPOSAL
Packaging:
Packaging can be fed into the reusable material cycle using the usual
disposal methods.
Please separate the packaging in accordance with the disposal laws and
recycling regulations in your country.
Product:
Dispose of the product in accordance with the applicable disposal regulations
in your country.
Subject to misprints and errors, as well as technical or other modifications!
Cameo ®
is a registered brand of the Adam Hall Group.
MAINTENANCE AND CARE
1. Only clean the softbox by hand using lukewarm water and mild soap. The softbox should not be
machine washed. To dry, please assemble completely and allow to air dry.
2. Please always ensure that you only pack and store the softbox when it is completely dry.
Permanent moisture can damage the laminated structure.
3. To fold, simply bring two diagonally opposite corners together.
After use, transport and store the softbox in the transport bag.
INSTALLATION
1. Remove the softbox from the transport bag and unfold it.
2. Bring the softbox with the back in front of the spotlight (see illustration) and pull
the corners of the softbox over the corners of the spotlight using the white loops (A).
The white bands inside the softbox (B) prevent the softbox from sliding too far over
the spotlight.
3. Now pull the four Velcro straps (C) through the four grip recesses on the sides of the
spotlight (D) and then through the corresponding plastic eyelets (E) on the top and
bottom edge of the rear part of the softbox, tighten the Velcro straps slightly and then join
hook side and loop side of the Velcro straps together.
4. Now attach the supplied diffuser cloth to the
front inner frame of the softbox using the sewn-on Velcro material.
A
C
D
D
A
C
B
B
MANUFACTURER'S DECLARATIONS
Manufacturer's warranty & limitation of liability
Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach, Germany / E-mail Info@adamhall.com /
+49 (0)6081 / 9419-0.
Our current warranty conditions and limitation of liability can be found at:
https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations-CAMEO_DE_EN_ES_FR.pdf.
Contact your distribution partner for service.
UKCA- CONFORMITY
Hereby, Adam Hall Ltd. declares that this product meets the following guidelines
(where applicable)
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulation 2012 (SI 2012/3032)
Radio Equipment Regulations 201 7(SI 2016/2015)
UKCA- DECLARATION OF CONFORMITY
Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or
RoHS Regulation can be requested at info@adamhall.com.
Products that are subject to the Radio Equipments Regulations 2017 (SI2017/1206) can be down-
loaded from www.adamhall.com/compliance/
Adam Hall GmbH | Adam-Hall-Str. 1
61267 Neu-Anspach | Germany
E
E
B
B
B
Phone: +49 60 81 · 94 19-0
adamhall.com