Bosch UniversalVac 15 Originalbetriebsanleitung Seite 17

Wet/dry vacuum cleaner
Net volume (liquid)
Dust bag volume
Max. vacuum in turbine
Max. flow rate of turbine
Automatic start/stop
Weight according to EPTA-Procedure 01:2014
Protection class
Protection rating
Mains plug Switzerland protection rating
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
A)
Automatic start/stop
Rated voltage
EU/AUS 220–240 V
UK 220–240 V
A) Permitted connected load of the connected power tool (country-specific)
Assembly
Pull the plug out of the socket before cleaning or per-
u
forming maintenance on the vacuum cleaner, making
tool adjustments, changing accessories or putting
away the vacuum cleaner. This safety measure prevents
the vacuum cleaner from being started accidentally.
Fitting the vacuum hose
Extraction Function (see figure A1).
Insert the vacuum hose (16) into the hose adapter (3) and
turn it clockwise as far as possible.
Blowing Function (see figure A2)
The vacuum cleaner has a blowing function. Do not
u
blow exhaust air out into the open air. Only use the
blowing function with a clean hose. Dust can be hazard-
ous to health.
– Switch on the vacuum cleaner for at least 5 seconds (on/
off switch (5)/mode selector switch (5) set to the "va-
cuum" symbol) to clean the vacuum hose (16) of dust de-
posits.
– Turn the vacuum hose (16) anticlockwise as far as pos-
sible and pull it out of the hose adapter (3).
– Open the exhaust air cover (26).
– Insert the vacuum hose (16) into the hose adapter (25)
and turn it clockwise as far as possible.
Fitting the Extraction Accessories
The vacuum hose (16) is equipped with a clip system which
can be used to connect vacuuming accessories (dust extrac-
tion adapter (17), curved nozzle (18)).
Bosch Power Tools
UniversalVac 15
l 8.5
l 11.8
mbar 240
l/s 65
kg 6.9
/ II
IPX4
IP55
Maximum power
2000 W
1800 W
Fitting the Dust Extraction Adapter or Curved Nozzle
(see figure B)
Fit the dust extraction adapter (17) or the curved
nozzle (18) to the vacuum hose (16) until the two snap
fasteners (27) on the vacuum hose audibly click into place.
To remove the adapter, press the snap fasteners (27) in-
wards and pull apart the components.
Fitting the nozzles and tubes
– Then attach the required vacuum accessory (floor nozzle,
crevice nozzle, suction tube, etc.) firmly to the curved
nozzle (18) or to the dust extraction adapter (17).
Changing/inserting the dust bag (dry
vacuuming) (see figure C1–C3)
To vacuum dry dirt, you can insert a dust bag (accessory).
This makes the dust easier to dispose of.
Replacing/Inserting Dust Bag (Accessories)
Open the catches (8) and remove the top part of the dust
extractor (7).
– Pull the full dust bag (29) backwards out of the connec-
tion flange (28) and remove it from the vacuum cleaner.
– Place the new dust bag over the vacuum cleaner's con-
nection flange. Make sure that the entire length of the
dust bag touches the inside wall of the container (1).
– Put the top part of the vacuum cleaner (7) on and close
the catches (8).
Replacing the inserts for the floor nozzle (see
figures D1–D2)
Depending on the vacuuming application (dry, wet, carpet,
etc.), you can clip various inserts (rubber lip, brush inserts)
into the floor nozzle (21).
– Press the release buttons (30) on the floor nozzle (21) to
release the insert from the floor nozzle.
English | 17
AdvancedVac 20
13.5
16.8
260
70
– ●
7.6
/I
IPX4
IP55
Minimum power
100 W
100 W
1 609 92A 7UL | (17.01.2023)