Bosch 1 609 92A 4XS AS Originalbetriebsanleitung Seite 16

Product Features
The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1) Tool holder
(2) Keyless chuck
(3) Torque presetting ring
(4) Gear selector
(5) Battery release button
(6) Battery A)
(7) Rotational direction switch
(8) On/off switch
1 609 92A 4XS | (22.02.2019) Bosch Power Tools
Cordless drill/driver UniversalDrill 18
Max. torque, hard/soft screwdriving
application ac cording to ISO 5393
mm 30/18
Max. drilling diameter (first/second gear)
– Steel mm 10 – Wood mm 30 Max. screw
diameter mm 8 Tool holder mm 10
over the total working period.
Implement additional safety measures to protect
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
kg 1.2–1.5 A)
– during charging °C 0 to +45 – during operation
°C -15 to +50 – during storage °C -20 to +70
Recommended batteries PBA 18 V...V-. PBA 18
Recommended chargers
– PBA 18 V....V-. AL 22.. CV AL 1810 CV
– PBA 18 V....W-. AL 1810 CV AL 1815 CV
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined
according to EN 62841-2-1.
Typically the A-weighted noise level of the power
tool is less than 70 dB(A). Uncertainty K = 5 dB.
The noise level when working can exceed
80 dB(A).
Wear hearing protection
A)
English | 13
times when the tool is switched off
or when it is running but not
actually being used should also be
Remove the battery from the
►
power tool before carry ing out
work on the power tool (e.g.
B)
V...W-.
AL 1815 CV
AL 1830 CV
AL 1880 CV
AL 1830 CV
AL 1880 CV
(9) Handle (insulated gripping surface)
(10) Universal bit holder
A) Accessories shown or described are not included
with the product as standard. You can find the
complete selection of accessories in our
accessories range.
Technical Data
Cordless drill/driver UniversalDrill 18
number 3 603 JC8 0.. Rated voltage V = 18
No-load speed
– 1st gear min -1 0–440 – 2nd gear min
To estimate vibration and noise emissions
accurately, the
taken into account. This may
significantly reduce vibration and
noise emissions
the oper ator from the effects of vibration, such as
servicing the power tool and application tools,
keeping their hands warm, and organising
workflows correctly.
Assembly
maintenance, changing tool,
etc.). The battery should also be
re
Total vibration values a
h
uncertainty K determined according to
EN 62841-2-1
Drilling in metal: a = 1.3 m/s
h
The vibration level and noise emission value given
in these instructions have been measured in
accordance with a standardised measuring
procedure and may be used to com pare power
tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission
value repres ent the main applications of the
power tool. However, if the power tool is used for
other applications, with different ap
plication tools or is poorly maintained, the
vibration level and noise emission value may
differ. This may significantly increase the
vibration and noise emissions over the total
working period.
moved for transport and storage. There is
risk of injury from unintentionally pressing the
on/off switch.
Charging the Battery
A)
Article
-1 0–1450
(triax vector sum) and
2 , K = 1.5 m/s 2 .