Konig & Meyer Ring Lock Bedienungsanleitung Seite 3

24169 Speaker wall mount
24169 »Ring Lock«
INTENDED USE
Speaker wall mount featuring the best workmanship and maneuverability.
For mounting speakers with flange sockets up to 25 kg.
FEATURES & CAPABILITIES
- Solid, durable steel construction
- Equally suitable for: home, commercial, and public use
- Versatile support arm:
- - With patented »Ring Lock« expanding mandrel to ensure wobble-free seating of the speaker:
- - ø 35 x 87 mm (suitable for flange sockets ø 35-36 mm)
- - Pivoting range approx. 120°; continuously adjustable
- - Inclination angle: 0°, 12,5° or 25°
Thank you for choosing this product. Please read and follow these instructions carefully. They will inform
you about all the important steps for assembly and handling. We recommend that you also keep them for
future use.
SAFETY INSTRUCTIONS
- Check the mount for damage before and after use.
- Damaged mounts must not be used again.
- Load capacity: max. 25 kg (centric load)
- Not for outdoor or damp areas
- Observe locally applicable mounting instructions (may differ from examples given)
- Only mount on a suitable wall with appropriate mounting material (not supplied);
- See section 3 for examples. Please observe the dowel manufacturer's installation instructions.
- Use 6 screws/dowels for wall mounting
- Walls that are too weak are unsuitable; also pay attention to power and water lines.
- If in doubt, consult a specialist.
- Check the strength and condition of the components and the screw fittings at regular intervals
- Installation only by trained installation personnel
- Attentive handling required, as the adjustment possibilities pose a pinching hazard
- When using the mount in "event and production facilities
- for scenic presentation", DBUV regulations 17 and 18 apply.
ASSEMBLY INSTRUCTIONS
1. COMPONENTS
Speaker wall mount 24169 consists of
a Wall plate
b Swivel/tilt joint
c Support arm
d Expanding mandrel
e Screw fittings
All components mentioned are already completely pre-
assembled. Please carry out a visual inspection to ensure that
all parts are present, and, as far as can be seen, are in good
order.
2. PREPARATION for WALL MOUNTING
2.1 Align wall mounting plate vertically
2.2 Mark drill holes 6x
2.3 Drill anchor/dowel holes 6x
2.3 - ø 8 mm for bolt anchors
2.3 - ø 10 mm for frame dowels
3. WALL MOUNTING EXAMPLES (A, B, C)
A Concrete wall example: bolt anchor M8 x 75 mm
3.1 Prepare
3.1 drill hole 6x
3.2 Set anchor/
3.2 dowel 6x
3.3 Fix
3.3 wall plate
3 C Suitable for both concrete and perforated bricks: injection mortar anchorages
3 C - WITHOUT sieve sleeve for solid masonry and concrete
3 C - WITH sieve sleeve for perforated bricks
Advantage: Fastening works without expansion pressure, thus the mount can be replaced as often as required
Advantage: and allows fastening close to edges (minimum distance 100 mm).
Advantage: For exact assembly instructions, please refer to the enclosed product information.
1. COMPONENTS and DIMENSIONS
2. PREPARATION for WALL MOUNTING
B Perforated brick example: frame dowel 10 x 100 mm
B with wood screw DIN571 ø 7 x 105 mm
- drill hole
- and blow out
- drive in
- anchor
- attach
- wall plate
- tighten
- nut with
- washer
- drill hole
- countersink
- blow out
- drive in
-
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2a, 97877 Wertheim, www.k-m.de
24169-000-55 Rev.01 03-80-921-00 12/22
frame dowel