Inhaltsverzeichnis
Werbung
6.1 PREPARATION
Before using the machine check for fuel and the
oil level. For refuelling and oil top-up methods and
precautionsent (seepar. 7.2 and par. 7.3).
Skids are used for adjusting the distance of the
auger from the ground to safeguard it.
Before using the machine, adjust the skids as
follows:
1. Slacken the screws (昀椀g. 14.A).
2. Lift/lower the skids (昀椀g. 14.B)
3. Tighten the screws.
6.2 SAFETY CHECKS
Ensure you have understood the contents before
proceeding. Run the following safety checks and
check the results correspond to those outlined in
the tables.
Always carry out the safety checks before
use.
6.2.1 General check
Object
Fuel lines and
connections.
Electrical cables.
Oil lines
Test driving
6.2.2 Traction and auger operation testing
Action
Start the machine (par. 6.3) The wheels and auger
Traction operation test
Press the forward control
(昀椀g. 12.D).
Release
the
forward
control (昀椀g. 12.D)
Auger operation test
Press the auger control
(昀椀g. 12.C)
Release the auger control. The auger stops.
Auger and wheel operation test
Result
No leaks.
All insulation intact.
No mechanical damage.
No leaks.
No damage.
No abnormal vibrations.
No abnormal sound.
Result
must stay still.
The wheels should move
the snow thrower forward.
The wheels stop.
The auger starts to rotate.
Action
Keeping the auger control
pressed
(fig.
press the forward control
(昀椀g. 12.D).
Release
the
control (昀椀g. 12.D).
Release the auger control
(昀椀g. 12.C).
If any of the results fails to match the
indications provided in the following table, do
not use the machine! Take it to a service centre
to be checked and repaired if necessary.
6.3 START-UP / OPERATION
1. Open the fuel tap (昀椀g. 13.B).
2. Insert the safety key and turn clockwise,
where indicated (昀椀g. 13.A).
6.3.1 Cold start
1. Turn the throttle to full on (昀椀g. 13.C).
2. Engage the choke (昀椀g. 13.D).
3. Press the primer bulb (昀椀g. 13.L) twice or three
times. Make sure that the hole is covered by
your 昀椀nger when pressing the bulb.
4. Start, using the electric control (par. 6.3.5) or
manual control (par. 6.3.3).
5. Disconnect the choke (昀椀g. 13.D).
IMPORTANT Before starting work with the
machine, wait a few minutes for the oil to warm up
. Warm start
1. Turn the throttle to full on (昀椀g. 13.C)
2. Check the choke is disconnected (昀椀g. 13.D).
3. Start the machine electrically or manually (see
below).
IMPORTANT During the warm start, do not
press the primer bulb.
6.3.2 Manual start-up
To manually start the engine, slowly pull the
handle (昀椀g. 13.H) outwards until resistance is felt.
Then pull sharply and accompany the handle as
you release it.
Repeat the operation until the engine starts.
NOTE Do not make more than 3/4 attempts,
otherwise you risk 昀氀ooding the engine. Check the
possible causes for a non-start in the "Problems
identi昀椀cation table".
EN - 8
Result
The auger should rotate
and the wheels move the
12.C),
snow thrower forward.
forward
The wheels rotate and the
auger continues to rotate.
The auger stops and the
wheels lock.
Werbung
Inhaltsverzeichnis
