Inhaltsverzeichnis
Werbung
the engine, remove the key, wait the moving
parts stop, and carefully inspect the machine
to check there is no damage. Vibrations are
normally synonymous with a problem. Repair
any damage before re-using the machine.
• Before leaving the machine, disconnect all the
commands and remove the ignition key from
its slot on the machine.
• Before
carrying
inspections or adjustments, switch o昀昀 the
engine, remove the key and wait the moving
parts stop (unless otherwise indicated in the
instructions). Disconnect the cable on electric
motors. (Optional).
• Do not touch the engine parts which heat up
during use. Burns hazard.
• Never operate the snow thrower at high
transport speeds on slippery surfaces. Use
care when reversing. Look behind you to make
sure there are no obstacles before and during
operations in reverse gear.
• Disengage power to the auger when snow
thrower is transported or not in use.
• Always be sure of your footing, and keep a 昀椀rm
hold on the handle. Walk never run.
Use limitations
• Do not use the machine sideways on a slope.
Always move from top to bottom, then from
bottom to top. Exercise caution when changing
direction on a slope. Avoid steep slopes.
• Do not use the machine if the guards are
insu昀케cient or if the safety devices are not
correctly positioned.
• Never disengage or tamper with the safety
systems.
• Do not alter the engine adjustments, nor over-
run it. If the engine is forced to work with an
excessive number of rotations, the risk of
personal injury increases.
• Do not overload the machine by driving it too
fast.
• Do not place hands inside the chute or the
auger without 昀椀rstly switching o昀昀 the engine
and removing the key.
2.4 MAINTENANCE,
TRANSPORT
Ensure regular maintenance and correct storage
to maintain machine safety.
Faulty or worn-out parts must always be
replaced and never repaired. Only use original
spare parts: the use of non-original and/
or incorrectly 昀椀tted parts will compromise
the safety of the machine, may cause
accidents or personal injuries for which the
Manufacturer is under no circumstance liable
or responsible.
out
repairs,
cleaning,
STORAGE
Maintenance
• If the fuel tank has to be drained, this should
be done outdoors and when the engine is cool.
• To reduce the risk of 昀椀re, regularly check the
machine for oil and/or fuel leaks.
Storage
• Do not leave fuel in the tank if the machine is
stored in a building where fuel vapours come
in contact with the open 昀氀ame, sparks or heat
sources.
• Let the engine cool down before storing the
snow thrower indoors.
• Always refer to owner's guide instructions for
important details if the snow thrower is to be
stored for an extended period.
Transport
• If the machine must be transported on a truck
or trailer, use ramps with suitable resistance,
width and length.
• Load the machine with the engine switched o昀昀
and pushed by an adequate number of people.
• During transport, close the fuel cock (if there
is one) and adequately secure the machine to
the means of transport using cables or chains.
2.5 ENVIRONMENTAL PROTECTION
Safeguarding the environment must be a relevant
and priority aspect of machine use, of bene昀椀t to
the community and the environment we live in.
• Avoid
neighbourhood.
• Adhere strictly to the local regulations
governing the disposal of packaging, oil, fuel,
昀椀lters, damaged parts or any other element
which may have an impact on the environment;
this waste should not be disposed of along
with standard household waste, but must be
disposed of separately and sent to special
waste disposal facilities for handling and
recycling.
• When the machine is withdrawn from service,
do not dump it in the environment, but take it to
a waste disposal facility in accordance with the
AND
local regulations in force.
EN - 3
being
a
disturbance
to
the
Werbung
Inhaltsverzeichnis
