Inhaltsverzeichnis
Werbung
NOTE The cables are already pre-assembled
on the dashboard.
4.3 HANDLE ASSEMBLY
The handle is delivered with the dashboard
already assembled. The screws for installing the
handle on the machine, the screws for securing
the gear control and the fasteners for attaching the
discharge chute and the gear lever and de昀氀ector
lever grips are all delivered in a separate package
inside the box with the machine.
Install as follows:
1. Bring the two tubes at the ends of the handle
(昀椀g. 6.A) up to the support (昀椀g. 6.B).
2. Insert the screws in the holes and secure in
place with the nuts.
4.3.1 Installation of the lever grips
Screw the grips onto the threaded rod of the
gear lever (昀椀g. 7.A) and the threaded rod of the
de昀氀ector adjustment lever (昀椀g. 7.B) accordingly.
Tighten the 昀椀xing nut.
4.4 INSTALLATION
CONTROL
1. Insert the articulated joint (昀椀g. 8.A) of the gear
control in the hole on the lever (昀椀g. 8.B) to
connect it to the transmission and secure in
place with the nut (昀椀g. 8.C).
2. Bring the top part (昀椀g. 8.D) of the gear control
up to the hole on the bottom part of the gear
lever and secure in place by inserting the peg
(昀椀g. 8.E) and the cotter pin (already on the
gear lever) (昀椀g. 8.F).
4.5 DISCHARGE CHUTE ASSEMBLY
1. Position the sliding ring (昀椀g. 9.A) and the
discharge chute (昀椀g. 9.B) on the 昀氀ange 昀椀tting
(昀椀g. 9.C).
2. Insert the skids (昀椀g. 9.D) under the 昀氀ange
昀椀tting (昀椀g. 9.C) by matching up the holes on
the skid with the holes at the bottom of the
chute.
3. Insert the screws with the washers (昀椀g. 9.E) in
the holes and fasten.
4.5.1 Installation of the discharge chute
adjustment cable
The adjustment cable is designed to connect
the discharge chute to the adjustment handle on
the dashboard so that the operator can point the
discharge chute in the required direction.
OF
THE
GEAR
1. Secure the worm screw unit onto the support,
checking the correct engagement of the worm
screw unit with the toothed section on the
discharge chute (昀椀g. 9.F).
2. Engage the square section of the 昀氀exible
cable in its seat at the bottom part of the
handle (if not already pre-assembled).
3. Tighten the cable ring nut (昀椀g. 10.B) on the
top part of the handle (昀椀g. 10.A) (if not already
pre-assembled).
4.5.2 Assembly of the de昀氀ector adjustment
cable
The de昀氀ector adjustment cable is designed to
connect the discharge chute de昀氀ector to the
control on the dashboard so that the operator can
lift/lower the de昀氀ector so that it is pointing in the
required direction.
1. Insert the peg (昀椀g. 11.B) on the end part of the
activation lever.
2. Insert the end of the adjustment wire (昀椀g.
11.C) on the peg (昀椀g. 11.B).
3. Insert the cotter pin on the peg and secure in
place (昀椀g. 11.D).
4. Insert the adjustment screw (昀椀g. 11.A) on the
housing (昀椀g. 11.E) and tighten the nut (昀椀g.
11.A).
5. CONTROLS
5.1 IGNITION KEY
Used to start and stop the engine. The ignition key
has two positions (昀椀g. 13.A):
1. Key removed - OFF - the engine stops and
cannot be restarted.
2. Key inserted - ON - the engine can start and
run.
IMPORTANT The engine cannot be started
unless the safety key is fully inserted. On some
models you also need to turn the key clockwise
to start it.
5.2 FUEL COCK
The fuel cock is opened to supply fuel (昀椀g. 13.B).
1. anti-clockwise - open.
2. clockwise - closed.
EN - 6
Werbung
Inhaltsverzeichnis
