Mounting The Forward Control And Auger; Handle Assembly; Gear Lever Assembly; Discharge Chute Assembly - Stiga ST 526 S Gebrauchsanweisung

J Screws for fixing the auger extension
4.1.1 Unpacking
1. Carefully open the packaging, paying
attention not to lose components
2. Consult the documentation in the
box, including these instructions.
3. Remove all the unassembled
parts from the box.
4. Take the snowplough out of the box.
5. Dispose of the box and packaging in
compliance with local regulations.
4.2 MOUNTING THE FORWARD
CONTROL AND AUGER CABLES
Hook the cable loop in the specific
eyelet (fig. 5.A, fig 5.B).
NOTE The cables are already
fitted in the dashboard.

4.3 HANDLE ASSEMBLY

The handle is delivered with the dashboard
already assembled. The screws for fitting
the handle on the machine, the screws for
fixing the gear lever, the screws for fixing the
discharge chute, the gear lever and deflector
lever grips are delivered in a separate
packaging inside the machine's packaging.
Mount as follows:
1. Bring the two end tubes of the handle
(fig. 6.A) close to the support (fig. 6.B).
2. Insert the spacers (fig. 6.C) and align
them with the holes, keeping in mind the
correct diameter (smaller cavity toward
outside, larger cavity toward inside).
3. Insert the screws, the washers and the
nuts in the holes and tighten them.
4.3.1 Lever grips assembly
Screw each grip in the threaded
rods of the levers (fig. 7).
Tighten the fixing nut until closed.

4.4 GEAR LEVER ASSEMBLY

1. Insert the joint (fig. 8.A) of the
gear lever in the hole of the lever
(fig. 8.B) to connect it to the transmission
and secure it with the nut (fig. 8.C).
2. Bring the upper part (fig. 8.D) of the gear
lever close to the hole of the lower part of
the gear lever and secure it by inserting
the pin (fig. 8.E) and the cotter pin (already
assembled on the gear lever) (fig. 8.F).
4

4.5 DISCHARGE CHUTE ASSEMBLY

1. Put the discharge chute (fig. 9.A) on the
flange coupling (fig. 9.B) making the two
holes at the base of the chute coincide.
2. Insert the screws and the washers in
the holes and tighten (fig. 9.C).
4.5.1 Connecting the discharge
chute guide cable
The purpose of the guide cable is to connect
the discharge chute to the guide handle
located on the dashboard, thus allowing
guiding the chute in the desired direction.
1. Insert the cable (fig. 9.D) and fasten the ring
nut on the rotation system of the chute.
4.5.2 Mounting the deflector's guide
cable (ST 526 S, ST 625, ST
665, ST 665 T, ST 726 T)
The purpose of the deflector's guide cable is to
connect the chute's deflector to the control lever
on the dashboard, allowing thus raising/lowering
the chute to guide it in the desired direction.
1. Insert the end of the guide cable
(fig. 10.C) on the pin (fig. 10.B).
2. Insert the cotter pin on the pin
and tighten (fig. 10.D).
3. Insert the adjustment screw (fig. 10.A) in its
seat (fig. 10.E) and tighten the nut (fig. 10.A).
4. Pass the cable on the oil plug fair-lead
carefully, to avoid getting close to the muffler.
4.5.3 Fastening the guiding connectors
of the deflector and of the
discharge chute (ST 767 H)
By connecting the guiding electrical connectors
of the deflector and of the discharge chute, power
is delivered to the system, allowing thus guiding
the discharge chute in the desired direction.
Fasten the connectors of the dashboard
power supply (fig. 11.A), of the deflector's
guiding cable (fig.11.B) and of the discharge
chute (fig. 11.C) to their couplers.
Pass the cable through the fair-lead
(fig. 11.D) behind the engine.
4.6 MOUNTING THE AUGER
EXTENSION (ST 767 H)
The auger extension allows collecting a
large quantity of snow in the auger, ensuring
thus easier and faster operation.
EN - 6