Specifications; Additional Safety Rules - Makita GV7000 Betriebsanleitung

ENGLISH
1 Cover
2 Side grip
3 Switch trigger
4 Lock button
5 Speed adjusting dial

SPECIFICATIONS

Model
Max. capacities
Abrasive disc ............................................................................ 180 mm
-1
No load speed (min ) ................................................................. 4,700
Overall length .............................................................................. 210 mm
Net weight ................................................................................... 2.0 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Always use eye and ear protection. Other per-
sonal protective equipment such as dust mask,
gloves, helmet and apron should be worn when
necessary. If in doubt, wear the protective equip-
ment.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
3. Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels
and other accessories running over rated speed
can fly apart and cause injury.
4. Check the backing pad carefully for cracks, dam-
age or deformity before operation. Replace
cracked, damaged or deformed pad immediately.
5. Check that the workpiece is properly supported.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Make sure abrasive disc is not contacting the
workpiece before the switch is turned on.
9. When sanding metal surfaces, watch out for fly-
ing sparks. Hold the tool so that sparks fly away
from you and other persons or flammable mate-
rials.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Pay attention that the wheel continues to rotate
after the tool is switched off.
12. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
4
Explanation of general view
6 Lock nut
7 Abrasive disc
8 Rubber pad
9 Spindle
10 Lock nut wrench
13. If working place is extremely hot and humid, or
14. Do not use the tool on any materials containing
15. Do not use water or grinding lubricant.
16. Ventilate your work area adequately when you
17. Always use the correct dust mask/respirator for
18. Ensure that ventilation openings are kept clear
SAVE THESE INSTRUCTIONS.
ENB048-3
OPERATING INSTRUCTIONS
Installing side grip (auxiliary handle) & cover
(Fig. 1 & 2)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip.
Install the cover, then screw the side grip on the tool
securely. The side grip and the cover can be installed on
either side of the tool. Always be sure that they are
installed securely.
Switch action (Fig. 3)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push in the lock button.
To stop the tool from the locked position, pull the trigger
fully, then release it.
11 Wrench
12 Limit mark
13 Brush holder cap
14 Screwdriver
GV7000
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
asbestos.
perform sanding operations.
the material and application you are working
with.
when working in dusty conditions. If it should
become necessary to clear dust, first disconnect
the tool from the main supply (use non metallic
objects) and avoid damaging internal parts.
GV7000C
180 mm
2,500 – 4,700
210 mm
2.0 kg