Emptying The Container; Cleaning The Device; Warranty Disclaimer - Hama PREMIUM M10 Bedienungsanleitung

5. Care and maintenance
Danger – risk of death from electric shock
Disconnect the mains plug from the socket before starting any cleaning work.
Warning - risk of cutting on the cutting rollers
Do not touch the cutting rollers.
Warning - damage to the device from moisture
Ensure, when cleaning, that no moisture penetrates the device in order to avoid
irreparable damage to it.

5.1 Emptying the container

Note
The status LED "Container full" on the " " button (9) ashes blue and the shredder
stops when the container is full.
• Switch the device off - as described in 4.2 Switching the device off - and disconnect
the mains plug.
• Pull the basket (5) out.
• Empty the container.
• Push the basket (5) back in.
• Reconnect the device - as described in 3. Installation/Setup - to the power supply.

5.2 Cleaning the device

• Switch the device off - as described in 4.2 Switching the device off - and disconnect
the mains plug.
• Clean the device with a dry cloth. In cases of heavy soiling, the cloth can be dampened
a little.
• Allow the device to dry completely afterwards.
• Reconnect the device - as described in 3. Installation/Setup - to the power supply.
5.3 Cleaning / oiling the cutting rollers
Note
• Oil the cutting rollers after each emptying of the waste paper basket in order to
prolong the shredder's service life.
• You can nd an appropriate selection of cleaning products at
www.hama.com.
• Switch the device on - as described in 4.1 Switching the device on.
5.3.1 Cleaning with Hama cleaners for shredders (item number: 113820)
• Apply the Hama cleaner for shredders (item number: 113820) in several strips onto a
piece of DIN A4-size paper.
• Insert the paper into the centre of the intake shaft (1). The cutting rollers switch on
automatically.
• Once the cutting process is complete, the device is ready for operation again.
5.3.2 Cleaning with cleaning paper
• Insert the cleaning paper into the centre of the intake shaft (1). The cutting rollers switch
on automatically.
• Once the cutting process is complete, the device is ready for operation again.
6. Troubleshooting
Error Possible cause
The " "
not pressed.
The cutting rollers do not
switch on automatically
The collecting container
when material to be
(5) is not inserted
shredded is inserted.
properly.
The connecting cable
(2) is not connected
correctly.
4
Remedy
Press the " " button
(9) until the status LED
button (9) was
"Ready" on the " "
button (9) lights up solid
blue.
Insert the collecting
container (5) properly.
Ensure that the mains
plug is in the mains
socket.
Error Possible cause
The cutting rollers do not
The socket is not live.
switch on automatically
when material to be
The device is faulty.
shredded is inserted.
The status LED "Overload" Too much paper has been
on the " " button (9) inserted or it has been
ashes red. drawn in at an angle.
The status LED
"Overheating" on the The device has become
" " button (9) lights up too hot.
solid red.
The status LED "Container
The collecting container
full" on the " " button
(5) is full.
(9) ashes blue.
The cutting rollers
continue to run after the There is jammed paper in
shredding process has the intake shaft (1).
been completed.
7. Technical data
Input voltage
Mains frequency
Max. power consumption
Dimensions (W x H x D)
Weight (net)
Weight (gross)
Basket capacity for paper and plastic cards
Max. noise level
Max. cutting performance - paper (70 gsm)
Max. cutting performance - paper (80 gsm)
Max. cutting performance - plastic cards
Max. cutting speed
Max. feed width for paper / plastic cards
Cutting size for paper / plastic cards
Max. constant operation time
Nominal rest period
Protection class (as per DIN 66399)
Safety levels (as per DIN 66399)
* Thicker paper, moisture or any voltage other than that permitted may reduce the
performance.

8. Warranty disclaimer

All of the technical information, data and instructions regarding operation contained in these
operating instructions was up to date at the time of printing and is provided based on previous
experience and to the best of our knowledge.
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failure to observe
the operating instructions and/or safety notes.
Remedy
Check the domestic fuses.
Notify Customer Services.
Follow the steps in
4.5 Forward/reverse
modes and clear the
paper jam
Switch the device off and
allow it to cool down for
at least 60 minutes.
Empty the container
(5) as described in
5.1 Emptying the
container.
Follow the steps as
described in 4.5
Forwards / backwards
modes. Switch off the
device and check for
pieces of paper stuck in
the intake shaft (1).
220 - 240 V~
50 Hz
380 W
35.0 x 51.9 x 24.6 cm
10500 g
12200 g
20 litres
62 dB
11 sheets (DIN A4 paper)*
10 sheets (DIN A4 paper)*
1
1.8 m/minute
220 mm
2 x 12 mm
15 minutes
Min. 60 minutes
3
P-5 / T-5 / E-4