AZURO 300 Anleitung Seite 20

EN
screw (A) to every matching four openings from the inside of the pool and fi x the corresponding nut
(B). Heads of the crews are inside the SP and their nuts are outside the SP.
f. First tighten the joints by hand. Finally, when all screws are in place, tighten them with tools.
g. Cover the front ends of the wall and heads of the screws on the inner side of the SP with an adhesive
tape, preferably with an adhesive textile tape (see Fig. 3-7).
h. Mask the overlapping sections of the wall ends and screw heads on the inner side of the pool wall
with an adhesive tape (see Fig. 3-7)., with the textile sticking tape, if possible.
Note: After the installation of the wall and measurement of the roundness of the SP, do not forget to take
out the central peg.
3. CHECK ON WHETHER THE WALL OF THE SP IS HORIZONTAL AND FORMS A CIRCLE
a. Use a long straight prism or profi le to check whether the opposite upper edges of the SP are levelled)
see Fig. 3-8). Check the wall in several various directions. The wall must rest on the horizontal plane.
Should the deviation from the horizontal plane over the diameter of the SP exceeds 25 mm (see the
fi g. 3-9), remove the wall and re-level the base of the SP.
b. Using a rope, check on whether the wall of the SP factually forms a circle.
Warning: A swimming pool not properly levelled may be dangerous as it may collapse.
4. FORM UP THE CORNER FILL
a. Use sieved sand or soil to form an arched fi ll approx.
20 cm wide and 20 cm high at the bottom of the wall along the entire perimeter inside the SP
(see 10). Form the arched part and compact it.
b. Now level the surface with a rake.
c. Place a geo-textile felt underlay on the bottom of the SP and the corner fi ll as a protection of the SP
liner against a mechanical damage. For the instruction see Annex A.
Note: If there is the danger of some grasses growing through and into the SP, we recommend to lay a
black garden liner under the SP bottom, which diminishes such danger.
Note: The SP felt underlay of geo-textile is not included in the package of the SP. Contact your vendor.
Aid: We recommend to use assembled ladder to enter and leave the SP. For the assembly instructions
see Annex B or C.
STEP C – INSTALLATION OF THE POOL LINER UND UPPER BAR
Note: If you plan to operate a fi ltration system for the SP, you have to carry out a part of the installation of
the skimmer prior to the fi xing of the pool liner. Read the respective instruction for the installation of the
skimmer and follow it.
1. SETTLE THE POOL LINER IN PLACE
a. Open the box containing the pool liner. Do not use any sharp objects to open the box.
b. Unroll and spread the pool liner on the sun, allow for a warm up. Check the surface of the liner and
all seams for openings.
c. Spread the liner (7) in the SP (see fi g.3-11) so that the faces of the seams were oriented upwards. The
arched seam should be in the centre of the arched part of the corner fi ll. Other seams will form lines
across the bottom of the swimming pool.
d. Smoothen all wrinkles of the pool liner on the bottom of the SP.
• 35 •
2. FIX THE POOL LINER TO THE WALL
a. Pull the pool liner [7] over the edge of the wall [1] and fi x it with several clasping bars [6] or with
laundry pegs temporarily at the place. For the time being, let the pool liner as it is. Do not tighten the
pool liner too much.
b. Start fi lling water to the SP. As the SP gets fi lled up, smoothen all wrinkles and smoothen the pool liner
in circles towards the wall. You can use a fi ne brush to that effect. Never push on the pool liner too
much and do not pull it. Proceed quickly as just few centimetres of water can squeeze the pool liner
to the bottom so that you can not move it anymore without damaging it. Keep the arched seam ap-
proximately in the centre of the corner fi ll. (see Fig.3-11)
c. Having smoothed the bottom, keep on adding water and smoothen the liner on the wall. Pay attention to
the fact that the SP liner should not get tightened and no air gap should be caused by that. (see Fig.3-13)
d. Having smoothened the pool liner, fi x the edge of the pool liner with the clasping bar [6]. Follow up
this way all along the perimeter of the SP:
e. Having fi rst pressed down the liner to remove all wrinkles from it, cut off the protruding part of the last
plastic clasping bar [6] so that its end rest just next to the following bar (see Fig. 3-12).
f. Now press the plastic rail [6] to the clasping bar [4]. Affi x another plastic rail [2] by means of a pair
of fl exible coupling connectors [4] and follow up this way all along the perimeter of the SP. (see Fig.
3-12)
Note: The delivered coupling connectors [2] are in two modifi cations – the connectors without a longitu-
dinal section are intended for the lower frame, the connectors with a longitudinal section are intended
for the upper frame.
g. Shorten the last plastic rail down to the required length and affi x it to the rest of the upper frame by
means of a pair of coupling connectors (see Fig. 3-12).
Note: A gentle corrugation of the pool liner during its installation is natural. It is caused by the play of the
vinyl material which protects the liner from shrinking.
Note: The liner is not a part of the SP construction. Its main function is to prevent water from leaking out of
the SP. The pressure of water is kept by means of the walls and parts of the SP construction. The liner must
properly adhere to the ground, the corner fi ll and the SP wall. It may never bear the weight of water which
might damage it.
3. FIX THE SELF-ADHESIVE WARNING LABEL
Next to point of entry to and exit from the SP, fi x the self-adhesive warning label. Keep in mind that the SP
is not deep enough for safe jumping. There is a risk of injury.
STEP D – FILLING THE SWIMMING POOL WITH WATER
1. COMPLETE THE FILLING OF THE SWIMMING POOL WITH WATER
a. Fill water to the SP up to the height of 5 cm bellow the lowest opening in the wall of the SP.
Thereafter proceed according to the instruction for the installation of the skimmer.
Important: The walls of the SP may experience some outward bulging or the SP may get shifted aside.
It is normal.
b. Connect the fi ltration system to the installed skimmer according to the respective instruction.
c. Add water up to the level of the centre of the inlet fl ange of the skimmer and carry out the fi rst sanita-
tion of water (see the Annex D). Now, your SP is ready for use.
Warning: Before anyone starts to use the SP, he/she has to read and comply with the Safety Rules as
contained in Part 4.
• 36 •
EN