Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ABOVE-GROUND CIRCULAR
SWIMMING POOL
Model 300 and 400
1. INTRODUCTION
1. READ THE INSTRUCTION MANUAL
Before you start, read all parts of the instruction manual up to its end.
The instructions explain how to install your swimming pool. Simply proceed according to the instruction
manual step by step. Start with Part 1 and proceed according to Parts 2 up to Part 3 when setting up your
swimming pool. Part 4 contains Safety Rules and Parts 5, 6 and 7 contain instructions that will help you to
keep your swimming pool clean and in a good condition for years. Be sure to read the Safety Rules and
make everybody who uses the swimming pool to read and understand the Safety Rules.
Note: Any fi gures shown in this manual may slightly differ from your swimming pool. The fi gures are pro-
vided fi rst of all for a better understanding of the text. The manufacturer reserves the right to alter the
manual without a previous notice.
2. GET NECESSARY EQUIPMENT READY
Before you start the installation of the swimming pool ("SP"), get necessary tools and equipment ready.
You will need the following:
•
spade, mattock, shovel and a wheelbarrow for the removal of excavated soil and sand handling.
•
wooden prism approx. 5 x 5 cm, its length should be longer than one half of the diameter of the SP,
wooden peg, package of fl our or fi ne sand etc., clue of cord, knife, water level, measuring band,
hammer and nails for the preparation of the fl at base
•
sieved pit sand for the levelling of the base
•
sieved pit sand for the levelling of the fi ll in corners
•
fl at-head screwdriver and cross-head screwdriver, combined pliers, textile (carpet) sticking tape,
knife, pool-assembling clothes-pegs
Prior to the assembly of the SP, we recommend setting up the ladder. You may need them during the
assembly of the SP when you have to step in and out from the SP over the set up wall. For the ladder as-
sembly instructions see Annex B or C.
3. SELECT A PROPER DAY FOR THE ERECTION OF THE SP
Wait for a sunny calm day for the assembly of the SP. Don't try to set up the SP when exposed to wind.
Invite at least one adult person to help you.
4. SPARE PART AND SERVICE
Should you need a piece of advice, service or spare parts, contact your vendor. Use only original spare
parts for the maintenance and repairs.
5. WARRANTY TERMS
For the warranty terms see the Warranty Certifi cate issued by the vendor.
• 31 •
PART 2 – PREPARATION OF THE SITE
STEP A – SELECTION OF THE SITE FOR THE ERECTION OF THE SWIMMING
POOL
1. GROUND
•
Pay special attention to the selection of a proper site for your SP.
•
Select a large area as fl at and horizontal as possible.
•
Select a place on a dry, solid and sun-bathed earth. So not erect the SP on asphalt, tarpaper, gravel,
peat swamp, wood, underfl ooded ground, or over any underground premises such as water reser-
voirs, sumps, sewers etc.
•
Check whether there are any plants on such an area that could grow through the liner of your SP. If
it be so, then we recommend to treat the site with a total herbicide (pursuant to the instructions) suf-
fi ciently in advance prior to the commencement of the ground works or, as the case may be, to lay
down a black garden liner under the body of the SP.
•
Any sloppy areas have to be levelled by digging upper positions away. Do not fi ll depressions. If nec-
essary, hire a system for the removal of soil.
The SP has not been designed for embedding to the ground.
2. CONDITIONS TO BE AVOIDED
Do not place the SP in the proximity of or immediately in any of the following places:
•
In the vicinity of areas and objects available to children and animals that could make the access
to the SP easier for them. If it be to the contrary, it is necessary to secure the surroundings of the SP in
order children and animals may be prevented from entering the SP.
•
Grass, stones, roots. Grass will get rotten bellow the pool liner and stones and roots will damage the
liner of the SP.
•
Branches of trees hanging over the SP. In the vicinity of trees and higher bushes. Leaves and other
impurities fall directly into the SP and increase its pollution.
•
Suspended electrical lines and clothes lines.
•
Places with a poor natural water drainage capacity as the environs of the SP may get fl ooded.
•
Any areas recently treated with oil-based pesticides, chemicals or fertilisers. In such a case use a felt
underlay bellow your SP made of geo-textile material.
3. PLAN IN ADVANCE
Do you wish to add an adjacent platform later on? Allow some space for it.
Keep in mind that the surrounding vegetation (trees, bushes) shall grow on and may put your SP into the
shade.
Will you use the accessories to the SP or some other system that need to be connected to a power
supply? Position your SP in a way allowing for the installation of such systems in compliance with safety
regulations (see the Instruction manual to this product). Any possible installation of an electrical socket
and an earth-leakage circuit-breaker must be carried out by a qualifi ed electrician.
STEP B – PREPARATION OF THE SWIMMING POOL BASE
Important: The area under the swimming pool must fulfi l the following basic conditions:
It must be horizontal.
i.e. having the tolerance of maximum 2,5 cm related to the transverse dimension of the swimming pool.
It must be provided with a thin layer of sieved sand,
i.e. that sand shall level small uneven places on the ground, which emerged after the tools (a mattock,
spade.... ) had been used, and shall cover the whole ground of the swimming pool with a layer not higher
• 32 •
EN
Werbung
