Rapid BHX50 Betriebsanleitung Seite 10

ADJUSTING TWIST LEVEL
To make the knots optimal for the type of branch-
es you tie, you can adjust the number of twists by
selecting "Twist level".
Twist level 1
Number of twists 2
FAILURE BEEP INDICATIONS
Buzzer Sound Frequency
Times
Single beep Battery capacity failure Check if battery capacity is low
Multiple beeps Internal tool failure
BATTERY PACK USE AND CARE
CAUTION!!
1. Only use battery charger as supplied together
with the tool, the use of other chargers may cause
fi re.
2. Only use, charge or store battery pack within the
specifi ed temperature range.
3. Below +4C°, battery capacity may be affected
and reduce the number of cycles.
4. Do not short-circuit the battery pack and ensure
to keep conductive items away from the battery
pack when not in use.
5. Do not disassemble the battery pack.
6. Do not use the battery pack close to any heat
source.
7. Do not put the battery pack in fi re or in water.
8. Do not make any harm to the battery pack.
9. Do not use a battery pack that is damaged, defor-
med or corroded.
10. Do not perform soldering or welding on the bat-
tery pack.
11. Do not use the battery pack on equipment other
than the designated tool.
12. Do not place the battery pack in microwave oven.
13. Do not use a battery pack that is leaking.
14. Keep the battery pack out of the reach of CHILD-
REN.
15. If you come into contact with a leaking battery
pack, wash with clear water immediately.
BATTERY PACK CHARGING
Connect the battery to the charger and connect the
charger plug to the power socket. The LED indicator
on the charger will turn RED during charging and
turn GREEN when the battery is fully charged; see
picture E2.
CAUTION!!
BATTERY PACK CHARGING
1. During charging, it is normal for the charger and
battery pack to be warm.
2. Do not charge a damaged battery pack and do
not disassemble the charger or battery pack.
3. Only charge the battery pack within the specifi ed
temperature range.
4. Do not place battery pack near a high tempera-
ture heat source; the battery pack may explode in
10
Twist selector
2 3
3 4
Failure Solution Method
Tool needs qualified service
fi re or fater a long exposure to a high temperature
heat source.
5. Do not charge the battery pack in an outdoor or
humid environment.
BATTERY PACK STORAGE
1. To ensure good battery pack storage, keep it
4
within the specifi ed temperature range.
5
2. If the equipment is not used for a long time, re-
move and charge the battery pack before storage.
3. It is recommended to place the battery and char-
ger in the tool's box during storage.
4. Battery should be stored in a dry environment
away from any infl ammables.
CHARGER USE AND CARE
CAUTION!!
Use the original charger to ensure the safety of the
equipment.
Only use a charger in good condition and never try to
use a defective charger.
Make sure that the supply voltage matches the rated
voltage of the charger nameplate.
Disconnect the charger from the power supply when
not in use.
Do not use the charger in an outdoor or humid envi-
ronment. The entry of dirt or water will increase the
risk of electric shock.
The charger shall only be used to charge the original
battery, otherwise it may result in personal injury and
cause a fi re.
Avoid any damage to the charger; a damaged charg-
er may increase the risk of electric shock.
Do not use chargers on fl ammable surfaces (e.g.
paper, textiles)
If the power supply cord of the charger is damaged, it
must be replaced by qualifi ed personnel.
WARNING!!
Disconnect battery before any maintenance
GENERAL CLEANING AFTER EACH SPOOL IS
FINISHED
The tool should be wiped with a wet cloth.
Use a paintbrush or similar to brush away foreign
matters in the guide lane, twister wheel and feeding
tray.
! Do not use any cleaning agent, as this may cause
permanent damage to the tool.
OIL & LUBRICATION AFTER EACH WORK DAY
Use good multigrade oil, for example 3-IN-ONE
or 15W-40. Lubricate each movable joint and the
cutter, see picture A13.
FEEDING DEVICE REPLACEMENT
When the feeding wheel no longer feeds the wire,
a replacement is recommended. Kit part number:
5001602
TWIST & HOOK DEVICE DEVICE REPLACEMENT
In case the twisting wheel stops twisting or you end
up with bad twists, a replacement is recommended.
Kit part number: 5001603
MAINTENANCE