Maintenance - AEG GS 400 Gebrauchsanleitung

TECHNICAL DATA
Nominal power output ........................................................
Rated output .......................................................................
No-load speed ....................................................................
Maximum no-load speed in case of ineffective no-
load speed limitation ...........................................................
Chuck neck diameter ..........................................................
Collet diameter ...................................................................
Abrasive grinding body diam. max.
ceramic or rubber bonded abrasive product ....................
resinoid-bonded abrasive product ...................................
Weight without cable ..........................................................
Typical weighted acceleration in the hand-arm area ..........
Typical A-weighted sound levels:
Sound pressure level .......................................................
The noise level when working can exceed 85 dB (A).
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
After switching off, the machine will not be idle immediately.
(After-running of the work spindle.) Allow the machine to
come to a stop before putting down.
Never reach into the danger area of the plane when it is
running.
Only use tools whose permitted speed is at least as high as
the highest no-load speed of the machine.
Check grinding tools before use. The grinding tool must be
properly mounted and turn freely. Perform a test run for at
least 30 seconds without load. Do not use damaged, out of
round or vibrating grinding tools.
When grinding metal, flying sparks are produced. Take care
that no persons are endangered. Because of the danger of
fire, no combustible materials should be located in the
vicinity (spark flight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust
flying from the workpiece come into contact with you.
The adjusting nut must be tightened before starting to work
with the machine.
Under the effect of extreme electromagnetic interferences
from the outside, temporary variations in the speed of
rotation could arise in particular cases.
Always use and store the grinding disks according to the
manufacturer's instructions.
The workpiece must be fixed if it is not heavy enough to be
steady. Never lead the workpiece to the grinding disk with
your hand.
SPECIFIED CONDITIONS OF USE
Straight grinders are suited for grinding metal, plastic, or
similar materials, especially in hard accessible corners and
places.
Do not use this product in any other way as stated for
normal use.
5 ENGLISH
GS 400 GS 500 E
......... 400 W .......................... 500 W ............... 500 W ......................... 600 W
......... 240 W .......................... 275 W ............... 300 W ......................... 350 W
..... 30000 min .......10000-29000 min
-1
..............- .......................... 38000 min
........... 43 mm ......................... 43 mm ................. - ................................. -
............. 6 mm ........................... 6 mm ................ 6 mm .......................... 6 mm
........... 25 mm ......................... 20 mm .............. 25 mm ........................ 20 mm
........... 50 mm ......................... 40 mm .............. 40 mm ........................ 40 mm
.......... 1,2 kg ........................... 1,3 kg ............... 1,8 kg ......................... 1,9 kg
............. 9 m/s .......................... 4 m/s
2
........... 79 dB (A) ..................... 79 dB (A) .......... 81 dB (A) .................... 79 dB (A)
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2, EN
61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Always disconnect the plug from the socket
before carrying out any work on the
machine.
GSL 500
...... 34000 min ......10000-29000 min
-1 -1
............... - ........................ 38000 min
-1
............... 7 m/s ......................... 3 m/s
2 2
Volker Siegle
Manager Product Development
GSL 600 E
-1
-1
2