Maintenance - AEG WS 6-100 Gebrauchsanleitung

TECHNICAL DATA
Rated input .........................................................................................
Output .................................................................................................
Max. no-load speed ...........................................................................
Grinding disk diameter .......................................................................
Thread of work spindle .......................................................................
Weight without cable ..........................................................................
Typical weighted acceleration in the hand-arm area .........................
Typical A-weighted sound levels:
Sound pressure level ......................................................................
The noise level when working can exceed 85 dB (A).
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Appliances used at many different locations including open air
must be connected via a residual current device.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Dust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out
any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
After switching off, the machine will not be idle immediately. (After-
running of the work spindle.) Allow the machine to come to a stop
before putting down.
Never reach into the danger area of the tool when it is running.
Always use the auxiliary handle.
Always use the protecting guard when roughing-down and
separating.
Only use tools whose permitted speed is at least as high as the
highest no-load speed of the machine.
Pay attention to the dimensions of the grinding disc. The mounting
hole diameter must fit the mounting flange without play. Do not
use reducer pieces or adapters.
Check grinding tools before use. The grinding tool must be
properly mounted and turn freely. Perform a test run for at least 30
seconds without load. Do not use damaged, out of round or
vibrating grinding tools.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in
order to find out the cause.
Always use and store the grinding disks according to the
manufacturer's instructions.
When grinding metal, flying sparks are produced. Take care that
no persons are endangered. Because of the danger of fire, no
combustible materials should be located in the vicinity (spark flight
zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust flying
from the workpiece come into contact with you.
Never use a cutting disc for grinding. Do not subject cutting discs
to side pressure.
The adjusting nut must be tightened before starting to work with
the machine.
The workpiece must be fixed if it is not heavy enough to be steady.
Never lead the workpiece to the grinding disk with your hand.
In case of extreme operating conditions (e.g. when smoothing
metals with the supporting disk and vulcanised fibre disks) strong
contamination can build up inside the angle grinder. In such cases
it is recommended to shorten the cleaning cycles and/or add a
residual current device.
Do not use any chainsaw or toothed saw blade. These frequently
cause jolting or lead to off control over the power tool.
For tools intended to be fitted with threaded hole wheel, ensure
that the thread in the wheel is long enough to accept the spindle
length.
SPECIFIED CONDITIONS OF USE
This angle grinder can be used for separating and grinding many
different materials, e.g. metal or stone. In case of doubt please
read the disk manufacturers' instruction.
Do not use this product in any other way as stated for normal use.
13 ENGLISH
All manuals and user guides at all-guides.com
WS 6-100
........... 670 W .......................... 670 W .......................... 700 W
........... 370 W .......................... 370 W .......................... 385 W
....... 11000 /min ................... 10000 /min ................... 10000 /min
........... 100 mm .........................115 mm ....................... 125 mm
......... M 10 ............................ M 14 ........................... M 14
............ 1,8 kg ........................... 1,9 kg ........................... 1,9 kg
............... 4 m/s
............. 82 dB (A) ..................... 82 dB (A) ..................... 82 dB (A)
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2, EN 61000-3-2,
EN 61000-3-3, in accordance with the regulations 98/37/EC,
89/336/EEC
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
Do not let any metal parts reach the airing slots - danger of short
circuit!
Use only AEG accessories and spare parts. Should components
need to be exchanged which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: AEG Elektrowerkzeuge, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
WS 6-115
........................... 4 m/s ........................... 4 m/s
2 2
Volker Siegle
Manager Product Development
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their
life must be collected separately and returned to
an environmentally compatible recycling facility.
WS 6-125
2