Maintenance - AEG WS15-125SX Betriebsanleitung

Supports must be placed under the workpiece near the line
of cut and near the edge of the workpiece on both sides of
the wheel.
f) Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Safety Warnings Specifi c for Sanding Operations:
a) Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations, when
selecting sanding paper. Larger sanding paper extending
beyond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc or kickback.
Safety Warnings Specifi c for Wire Brushing
Operations:
a) Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire
brushing, do not allow any interference of the wire
wheel or brush with the guard. Wire wheel or brush may
expand in diameter due to work load and centrifugal forces.
Additional Safety and Working Instructions
When grinding metal, fl ying sparks are produced. Take care
that no persons are endangered. Because of the danger of
fi re, no combustible materials should be located in the
vicinity (spark fl ight zone). Do not use dust extraction.
Avoid fl ying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is
running.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the
machine in order to fi nd out the cause.
Under extreme conditions (e.g. smooth-grinding metals
with the arbour and vulcanized fi bre grinding disk),
signifi cant contamination can build up on the inside of the
angle grinder (metal residue/deposits). For safety reasons,
in such conditions a ground fault interrupter must be
connected in series. If the ground fault interrupter trips the
machine must be sent for service.
Sawdust and splinters must not be removed while the
machine is running.
MAINS CONNECTION
Connect only to single-phase AC current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
Appliances used at many diff erent locations including wet
room and open air must be connected via a residual
current device (FI, RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched off .
Do not let any metal parts reach the airing slots - danger of
short circuit!
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment
may be aff ected. If the system impedance of the power
supply is lower than 0,2 Ohm, disturbances are unlikely to
occur.
SPECIFIED CONDITIONS OF USE
The angle grinder is intended for grinding and cutting
metal, stone and ceramic materials as well as sanding and
wire brushing.
Use the safety guard from the accessories range when
performing out cutting work.
22 ENGLISH
Please refer to the instructions supplied by the accessory
manufacturer
The machine is suitable only for working without water.
WORKING INSTRUCTIONS
For accessories intended to be fi tted with threaded hole
wheel, ensure that the thread in the wheel is long enough
to accept the spindle length.
Always use and store the cutting and grinding disks
according to the manufacturer's instructions.
Always use the correct guard for cutting and grinding.
Always use guard with cutting guide from the accessories
range for cutting stone.
The grinding surface of the centre depressed wheels must
be mounted min. 2 mm below the plane of the guard lip.
The adjusting nut must be tightened before starting to work
with the machine.
Always use the auxiliary handle.
The workpiece must be fi xed if it is not heavy enough to be
steady. Never move the workpiece towards the rotating
disk by hand.
STARTING CURRENT LIMITER + SMOOTH START
The starting current for the machine is several times
greater than rated current. The starting current limiter
reduces the starting current to such an extent that a fuse
(16 A, slow-blow) is not tripped.
Electronic smooth start for save use prevents jerky run-up
of the machine.
ELECTRONICS
The speed of rotation is adjusted electronically when the
load increases.
In case of a longer overload period the speed is decreased
electronically. The machine continues to run slowly to cool
down the motor coil. After switching off and on the machine
can be used at rated load.

MAINTENANCE

The ventilation slots of the machine must be kept clear at
all times.
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the
service organization.
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
STARTUP PROTECTION
A zero-voltage switch prevents the machine from restarting
after a power failure. On resuming work, switch the
machine off and then back on again.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-3:2011+A2:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2020-12-15
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-3:2011+A13:2015
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018
Winnenden, 2020-12-15
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear gloves!
Do not use force.
Only for grinding.
Only for cutting work.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool, tool in which protection against
electric shock does not rely on basic
insulation only, but in which additional safety
precautions, such as double insulation or
reinforced insulation, are provided.
There being no provision for protective
earthing or reliance upon installation
conditions.
European Conformity Mark
British Confomity Mark
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 23