Inhaltsverzeichnis
Werbung
1.
GENERAL INFORMATION
1.1.
SCOPE OF THE MANUAL
To make it easier to read about and look up various
subjects, refer to the table of contents at the begin-
ning of the section in your language.
This manual has been prepared by the manufacturer
and is an integral part of the product. As such, it must
be kept in a safe place for the machine's entire service
life until demolition.
The customer must ensure that machine operators
have read or are familiar with the contents of this
manual so that they strictly follow the instructions
described herein.
Constant compliance with the instructions provided
in this manual is the only way to guarantee the best
results in terms of safety, performance, efficiency and
service life of the product you now own. Non-com-
pliance with these rules may cause injuries to people
and damage to the machine, the scrubbed surface
and the environment: in no case can such injuries or
damage be attributed to the manufacturer.
This manual refers in detail to the machine and pro-
vides instructions and descriptions only about our
batteries and battery chargers (optional).
The batteries and the battery charger are basic com-
plementary machine parts and will affect its operation
in terms of running time and performances. Only the
correct combination of the two accessories (batteries
and battery charger) will ensure the highest possible
performances and avoid wasting lots of money. For
more detailed information refer to the special battery
and battery charger manuals.
Our recommended battery chargers and batteries
(optionals) ensure the best combination with the
machine and offer outstanding versatility (battery
charger) as well as the category's highest quality and
performance standards.
1.2.
TERMINOLOGY AND SYMBOL LEGEND
For the sake of clarity and to efficiently highlight the
various aspects of the instructions provided, terms
and symbols were used that are defined and illustra-
ted here below:
- Machine. This definition replaces the commercial
name to which this manual refers.
- Operator. An operator is considered the person
who normally uses the machine and is familiar with
its operating features but does not have the specific
technical skills to work on that machine.
- Technician. A technician is considered a person
who has the experience, technical education, legi-
slative and regulatory knowledge that allows him to
carry out any type of required work, and the ability to
recognise and to avoid possible risks during machine
installation, operation, handling and maintenance.
☞ - INDICATION SYMBOL. Particularly important in-
formation to avoid machine malfunctions.
• - ATTENTION SYMBOL. Very important informa-
tion to avoid serious damage to the machine and to
the environment in which it operates.
• - DANGER SYMBOL. Vital information to avoid se-
rious (or extreme) consequences affecting the health
of persons and causing damage to the product and
the environment in which it operates.
1.3.
PRODUCT IDENTIFICATION
The nameplate located under the dashboard contains
the following information:
• manufacturer ID
• CE mark
• model code
• model
• overall power rating
• serial number
• year built
• weight with maximum load
1.4.
SPECIFIC USE
This machine is a floor scrubber-drier: it must be used
to scrub and to vacuum liquids of flat, rigid, horizon-
tal, smooth or moderately rough and uniform floors
that are free from obstacles in both civic and indu-
strial environments. Any other use is prohibited.
Please refer very carefully to the safety information
reported in this manual.
The scrubber-drier distributes a quantity of a water
and detergent solution (adjustable) on the surface
to be cleaned, while the brushes remove any dirt on
the ground. The machine's suction system, using a
ground squeegee, perfectly dries the liquids and the
dirt just removed from the front brushes in a single
pass.
By efficiently combining a cleaning detergent with
various types of brushes (or abrasive disks), the ma-
chine can adapt to all the various combinations of
floors and dirt.
1.5.
TECHNICAL MODIFICATIONS
This machine was designed and built in accordance
with the fundamental requirements for user safety
and health as set forth in European directives. For
this reason the CE mark was placed on the ID label.
The European directives to which the equipment con-
forms are referenced in the Certificate of conformity
annexed to this manual. This certificate will no longer
be valid if the equipment is modified in any way wi-
thout the manufacturer's prior authorisation.
The manufacturer reserves the right to make techni-
cal modifications to the product, without prior notice,
in order to make the necessary technical upgrades or
improvements. For this reason, some details of your
machine may be different from the information in the
sales catalogues or from the illustrations presented in
24
Werbung
Inhaltsverzeichnis
