Fein GRIT GI100 Originalbetriebsanleitung Seite 12

en
12
The mains plug of the machine may be mounted only by
a qualified electrician. The protective conductor in the
mains socket outlet must be connected with the pro-
tective earthing of the mains supply.
Pull out the mains plug for maintenance and repair!
Switching the machine on unintentionally can lead to
serious injuries.
Have the electrical safety of the machine checked reg-
ularly in accordance with statutory regulations. For
machines that have not been checked, there may be
danger of electrical shock!
Check the rotation direction of the motor before start-
ing the operation of the machine for the first time. If the
rotation direction of the motor is incorrect, the work-
piece can be thrown from the machine and cause an
accident. The rotation direction may be changed only
by a qualifiedelectrician.
Make sure that you or other persons are not standing
directly next to the grinding belt when switching the
machine on. The grinding belt can tear apart and cause
serious injuries.
Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
At a glance.
1 Star-knob bolt for adjusting the tracking of the
grinding belt
2 Safety cover, top
3 Adjustment screw of support surface for plane
grinding
4 Star-knob bolt of top safety cover
5 Stop
6 Wing bolts of the spark guard
7 Spark guard
8 Grinding rest
9 Screw for grinding rest
10 Star-knob bolt of front safety cover
11 Clamping lever
12 Safety pushbutton
13 Venting slots
14 On/Off switch
15 Contact wheel
16 Support surface for plane grinding
17 Drive wheel
18 Side cover
19 Screw for side cover
20 Hose connection socket for dust extraction
21 Instruction label
22 Fastening screws of sub base for work bench
23 Star-knob bolt, top cover and side cover
Assembly instructions (figure 6).
Fasten the machine on the Fein sub base GIXS or
GIXBE (see Assembly instructions) or on a work bench
with fitting bolts (22).
Fasten the sub base or the work bench to the floor
using suitable dowel/bolt connections.
All connections must withstand the forces that arise
during working.
Faulty assembly can cause the sub base or work bench
to tilt over or the machine to loosen from the sub base
or work bench during operation, and lead to serious
accidents.
Electrical connection.
The electrical connection, which is to be pro-
vided by customer, must be carried out by a qual-
ified electrician.
Observe mains voltage: The mains voltage and the fre-
quency of the power source must agree with the data
onthe type plate of the machine.
Before starting operation for the first time, check the
rotation direction of the motor. The rotation direction
may be changed only by a qualified electrician.
Adjustments.
Before any work on the machine itself, pull the
mains plug.
Adjusting the spark guard (7).
Loosen both wing bolts (6) and adjust the spark guard
(7) in such a manner that the grinding belt is covered off
as far as possible.
Tighten both wing bolts again.