Elica CIAK 2.0 S Montage- Und Gebrauchsanweisungen Seite 5

● Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or
other fuels (including those in other rooms) due to back flow of combustion gases. These gases can potentially result in
carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of flued gas
appliances should be tested by a competent person to ensure that back flow of combustion gases does not occur.
INSTALLATION SAFETY
•Use the fixing screws supplied with the product only if suitable for the surface; otherwise purchase the correct type of
screws. •Check for accessories (e.g. bags containing screws, warranty certificates, etc.) inside the product (placed there
for transport reasons). If there are any, remove them and keep them safe. • WARNING: Failure to install screws and
fasteners in accordance with these instructions may result in electrical hazards. •The exhaust pipe is not supplied and
must be purchased. •The diameter of the exhaust pipe must be equivalent to the diameter of the connecting ring. •For
installation of the product on the hob, respect the height indicated in the drawings •The minimum distance between the
surface of the container supports on the cooker and the lowest part of the range hood must not be less than 50 cm (not
less than 65 cm only for Australia and New Zealand) for electric cookers and 65 cm for gas or mixed cookers. •If the
installation instructions of the gas cooker specify a greater distance, take it into account.
ELECTRICAL CONNECTION SAFETY
•The mains voltage must correspond to the voltage indicated on the label found inside the product. •If it features a plug,
connect the product to a socket that complies with current standards, located in an area accessible even after installation.
•If it does not feature a plug (direct connection to the mains) or the plug is not located in an accessible area, even after
installation, apply a standard double pole switch that ensures complete disconnection from the mains in category III
overvoltage conditions, in accordance with the installation rules. •The product features a special power cable; if the cable
is damaged, contact the Service Centre for a replacement.
MAINTENANCE WARNINGS
• Cleaning: For cleaning, simply use a cloth moistened with neutral liquid detergents. Do not use cleaning tools or
instruments.
For product maintenance, see the images at the end of the installation marked by this symbol.
• Anti-Grease Filter: The metallic anti-grease filter must be cleaned once a month with non-aggressive detergen-
ts, manually or in a dishwasher on a short wash at low temperatures. To remove the anti-grease filter, pull the spring re-
lease handle.
• Carbon filter (for filter version only): The cartridge must be replaced at least every four months. It CANNOT
be washed or regenerated. As indicated in the drawings section: remove the anti-grease filters, apply a carbon filter on
each side and attach it to the product. Put the anti-grease filters back in place.
Illumination
• Lighting system : The lighting system cannot be replaced by the user, contact Customer Service in case of malfunc-
tion.
• Lamp Replacement : Disconnect the product from the electrical power supply. Please note! Before touching the lamps,
make sure they have cooled. For the type of lamp to use, see the indications in the drawings section.
END-OF-LIFE DISPOSAL
This device is marked in compliance with the European Directive 2012/19/EC - UK SI 2013 No.3113, Waste
Electrical and Electronic Equipment (WEEE). Make sure that this product is disposed of correctly. The user helps
prevent potential negative consequences for the environment and for health.
The symbol on the product or accompanying documentation indicates that this product should not be treated as
household waste but should be handed over at a suitable collection point for the recycling of electrical and electronic
equipment. Dispose of it in accordance with local regulations for waste disposal. For further information about the
treatment, recovery and recycling of this product, please contact your local authority, the collection service for household
waste or the shop from where the product was purchased.
REGULATIONS
Equipment designed, tested and manufactured in compliance with safety regulations: EN/IEC 60335-1; EN/IEC 60335-2-
31, EN/IEC 62233. Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC
60704-2-13;EN/IEC 60704-3; ISO 3741; EN 50564; IEC 62301. EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR
14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3.
5