Inserting And Removing The Battery - Bosch Intuvia 100 Benutzerhandbuch

To charge the battery, read and follow the instructions in the
operating manual for the charger.
The battery can be charged at any state of charge. Interrupt-
ing the charging process does not damage the battery.
The battery has a temperature monitoring function which
only allows it to be charged within a temperature range of
0 °C to 40 °C.
Do not reconnect the battery to the charger until it has
reached the correct charging temperature.
Battery charge indicator
The five LEDs on the battery charge indicator (6) indicate
the battery's state of charge when the battery is switched
on.
Each LED represents approximately 20% of the charging ca-
pacity. When the battery is fully charged, all five LEDs will be
lit.
The battery's state of charge when switched on is also shown
on the display of the on-board computer. Read and follow
the instructions in the operating manuals for the drive unit
and on-board computer.
If the battery capacity is less than 10%, the last remaining
LED will flash.
If the battery capacity is less than 5%, all the LEDs on the
battery charge indicator (6) on the battery will go out. The
display function of the on-board computer, however, will
carry on working.
Once charging is complete, disconnect the battery from the
charger and the charger from the mains.

Inserting and removing the battery

Always switch off the battery and the eBike system
u
when inserting the battery into the holder or remov-
ing it from the holder.
Removing the PowerTube battery (pivot) (see figure A)
❶ To remove the PowerTube battery (4), open the
lock (2) using the key (1). The battery will be unlocked
and fall into the safety restraint (8).
❷ Press on the safety restraint from above. The battery
will be unlocked completely and fall into your hand.
Pull the battery out of the frame.
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the PowerTube battery (pivot) (see figure B)
In order for the battery to be inserted, the key (1) must be
inserted into the lock (2) and the lock must be open.
Bosch eBike Systems
If the temperature of the bat-
tery is outside this charging
range, three of the LEDs on
the battery charge indicator
(6) will flash. Disconnect the
battery from the charger and
let it acclimatise.
❶ To insert the PowerTube battery (4), place it so that its
contacts are in the lower holder of the frame.
❷ Push the battery upwards until it is held by the safety
restraint (8).
❸ Hold the lock open with the key and press the battery
upwards until you hear it click into place. Check that
the battery is secure in all directions.
❹ Always secure the battery by closing the lock (2) –
otherwise the lock may open and the battery may fall
out of the holder.
Always remove the key (1) from the lock (2) after locking it.
This prevents both the key from falling out and the battery
from being removed by unauthorised third parties when the
eBike is not in use.
Removing the PowerTube battery (axial) (see figure C)
❶ To remove the PowerTube battery (12), open the
lock (2) using the key (1), remove the key (1) and fold
the locking mechanism (9) to the side.
❷ Use the pull strap (10) to pull the battery (12) out of
the frame and keep hold of it so that it does not fall out
of the frame.
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the PowerTube battery (axial) (see figure D)
In order for the battery to be inserted, the locking mechan-
ism (9) must be folded to the side. At this point, the key (1)
must not be inserted in the battery lock (2).
❶ To insert the PowerTube battery, insert it into the
frame with the socket for the charging connector (5)
facing upwards until the battery clicks into place. En-
sure that the battery is aligned correctly.
❷ Close the locking mechanism (9), insert the key (1)
into the battery lock (2) and secure the battery. Make
sure that the safety hook (3) is hooked in at the open-
ing of the axial rail (11).
❸ Check that the battery is secure in all directions.
Always remove the key (1) from the lock (2) after locking it.
This prevents both the key from falling out and the battery
from being removed by unauthorised third parties when the
eBike is not in use.
Inserting and Removing the PowerPack battery
(see figure E)
In order to insert the battery, the key (1) must not be inser-
ted in the lock (2).
To insert the PowerPack battery (15), place it so that its
contacts are in the lower holder (16) on the eBike. Tilt it into
the upper holder (14) as far as possible until you hear it click
into place.
Check that the battery is secure in all directions.
Do not ride with the key (1) inserted. Make sure that the key
is no longer inserted when you park the eBike.
To remove the PowerPack battery (15), switch it off and
open the lock (2) using the key (1).
225
English – 3
0 275 007 3PX | (25.05.2022)