Starting Operation - Bosch Intuvia 100 Benutzerhandbuch

English – 2
SmartphoneGrip
Inductive charging capacity
Operating temperature
Storage temperature
Protection rating
Weight, approx.
Assembly
SmartphoneGrip Assembly (see figure A)
Press and hold the release mechanism (4) to position the
SmartphoneGrip. Place the upper edge of the Smart-
phoneGrip next to the snap-in hook (6) of the display
holder (5) ➊. Pull the SmartphoneGrip towards you and
push the SmartphoneGrip onto the display holder ➋. Let go
of the release mechanism (4).
Press the release mechanism (4) while pulling it towards
you ➊ to remove the SmartphoneGrip. Remove the Smart-
phoneGrip and let go of the release mechanism (4) ➋.
Inserting the Removal Blocker (see figure B)
Insert the removal blocker (12) into the adapter tray (16)
from below until you hear the removal blocker (12) click into
place.
Together with the keypad lock (13), this prevents the Smart-
phoneGrip from being quickly and easily removed.
Note: The removal blocker (12) is not an anti-theft device.
To remove the removal blocker (12), loosen the two fasten-
ing screws (11).
Smartphone Assembly (see figure C)
The SmartphoneGrip can hold smartphones in the following
sizes:
The specified dimensions include any phone cases. Smart-
phones with folio and carrying cases must not be used.
The total weight must not exceed 276 g.
0 275 008 3SG | (28.02.2022)
W 7.5 W (1.5 A at 5 V)
Efficiency > 67 %
°C –5 to 40
°C 10 to 40
IP54
g 75
Insert your smartphone (15) with the long side of the phone
positioned at the centre against the movable retaining
bracket (1). Press the smartphone (15) against the movable
retaining bracket (1) with both hands ➊ and place your
smartphone (15) in the SmartphoneGrip ➋.
Be careful not to pinch your fingers between the movable
u
retaining bracket and the SmartphoneGrip when inserting
your smartphone.
Once you have inserted your smartphone, check that the
smartphone cannot come into contact with any hard parts on
the bike even in case of vibrations, as this could cause last-
ing damage to the smartphone.
Keypad Lock Assembly (see figure D)
The keypad lock (13) supplied, together with the removal
blocker (12), prevents the SmartphoneGrip from being
quickly and easily removed by blocking the release mechan-
ism (4).
To insert the keypad lock (13), slide the keypad lock (13)
into the provided opening ➊ and carefully screw it into place
with a hex key (1.5 mm) (14) ➋.
Note: The keypad lock is not an anti-theft device. The
keypad lock prevents the SmartphoneGrip from being
quickly removed from the holder. The keypad lock does not
affect the smartphone in any way.
Note: Never leave your smartphone unattended in the
SmartphoneGrip.
To remove the keypad lock (13), unscrew the securing
screw with a hex key (1.5 mm) (14) and remove the keypad
lock (13).
Operation

Starting Operation

Place your smartphone in the SmartphoneGrip.
Start the eBike Flow app to have riding data displayed.
Depending on the smartphone's operating sys-
tem, the eBike Flow app can be downloaded
free of charge from the Apple App Store and
the Google Play store.
Use your smartphone to scan the code in order to download
the eBike Flow app.
Charging your Smartphone
While the smartphone is in the SmartphoneGrip, it can be
charged at the same time as displaying riding data. If your
smartphone has an inductive charging function, you can
charge the smartphone without needing a cable.
Inductive Charging
The charging process starts automatically when you place a
smartphone with an inductive charging function in the
SmartphoneGrip. The status LED (9) lights up yellow. When
the smartphone is fully charged, the status LED (9) will light
up green permanently.
146
Bosch eBike Systems