Bosch Intuvia 100 Benutzerhandbuch Seite 100

English – 6
3. If you are handing in your eBike to a bicycle dealer for
maintenance, it is recommended that you temporarily
deactivate the <eBike Lock> to prevent false alarms.
Software updates
Software updates must be manually started in the eBike
Flow app.
Software updates are transferred to the operating unit in the
background of the app as soon as it is connected to the app.
During the update process, a green flashing on the battery
charge indicator (13) shows the progress. The system is
then restarted.
You can control the software updates via the eBike
Flow app.
Connecting the System Controller to the Mini
Remote
The System Controller and Mini Remote operating units
are connected via Bluetooth®.
Switch on the eBike system and do not start riding the eBike.
If the Mini Remote operating unit has not already been con-
nected to the System Controller operating unit by the bi-
cycle dealer, proceed as follows:
1. First connect your smartphone to the System Control-
ler operating unit via the eBike Flow app (see Establish-
ing a smartphone connection).
2. In the eBike Flow app, select <Connect the Mini Re-
mote>.
You will be asked to switch the System Controller and
Mini Remote to pairing mode.
3. System Controller: Start the pairing process by press-
ing and holding (3 s) the on/off button (12) until the
lower bar on battery charge indicator (13) shows the
pairing process by flashing blue.
4. Mini Remote: Start the pairing process by pressing any
button until the pairing process is shown by the LED in-
dicator light (3) flashing blue.
5. Follow the instructions in the eBike Flow app.
If pairing is successful, this is shown within 30 s on the Mini
Remote operating unit by the LED indicator light (3) flashing
green three times.
If the connection cannot be established, this is shown by the
LED indicator lamp (3) flashing red three times. Repeat the
connection process.
If you want to connect the Mini Remote operating unit to a
System Controller on another eBike, the following steps
must be carried out:
1. Mini Remote: Remove the battery on the Mini Remote
operating unit and reinsert it.
2. Within the next 10 s, press and hold the decrease as-
sistance –/walk assistance (6) button for 5 s.
The pairing process is shown by the LED indicator light
(3) flashing blue for 30 s.
3. System Controller: Start the pairing process by press-
ing and holding (3 s) the on/off button (12) until the
0 275 007 3RC | (25.03.2022)
lower bar on battery charge indicator (13) shows the
pairing process by flashing blue.
If pairing is successful, this is shown within 30 s on the Mini
Remote operating unit by the LED indicator light (3) flashing
green three times.
If the connection cannot be established, this is shown by the
LED indicator lamp (3) flashing red three times. Repeat the
connection process.
Error messages
The operating unit shows whether critical errors or less crit-
ical errors occur in the eBike system.
The error messages generated by the eBike system can be
read via the eBike Flow app or by your bicycle retailer.
Via a link in the eBike Flow app, information about the error
and support for rectifying the error can be displayed.
Less critical errors
Less critical errors are shown by the assistance level LED
(10) flashing orange. Press the select button (5) on the Mini
Remote (1) operating unit or the mode button (14) on the
System Controller (2) operating unit to confirm the error.
The assistance level LED (10) once again continuously
shows the colour of the set assistance level.
You can use the following table to rectify the errors yourself
if necessary. Otherwise, please contact your bicycle retailer.
Number Troubleshooting
523005 The indicated error numbers show that
there is interference when the sensors de-
514001
tect the magnetic field. See whether you
514002
have lost the magnet while riding.
514003
If you are using a magnet sensor, check that
514006
the sensor and magnet have been properly
installed. Make sure too that the cable to the
sensor is not damaged.
If you are using a rim magnet, make sure that
you do not have any magnetic field interfer-
ence in the vicinity of the drive unit.
Critical errors
Critical errors are shown by the assistance level LED (10)
and the battery charge indicator (13) flashing red. Follow
the instructions in the table below if a critical error occurs.
Number Instructions
660001 Do not charge the battery and do not
continue to use it.
660002
Please contact your Bosch eBike
dealer.
890000 – Acknowledge the error code.
– Restart the system.
If the problem persists:
– Acknowledge the error code.
– Perform software update.
– Restart the system.
100
Bosch eBike Systems