Hama EWS-100 Bedienungsanleitung Seite 4

g Operating Instruction
MODE CHANNEL MAX/MIN
SET/AL
DOWN
ON/OFF
12/24
UP °C/°F
RESET
ALERT
Features and Specifications
Base Station
• Indoor/outdoor RF temperature
• Monitors temperature at up to 4 locations
(additional sensors required)
• Indoor/outdoor temperature displayed in °C or °F
• Memory funcion to recall highest/lowest temperature
readings
• Indoor temperature range: -10°C to 70°C
(14°F to 158°F)
• Temperature tolerance: +/– 1,1°C (+/– 2°F)
• 12/24 hour selectable alarm clock with snooze
• Month/day/year calender
• Countdown timer
• Low battery indicator
• Table top or wall mount
• Requires 2 AAA batteries
6
Remote Sensor
• 433 MHz transmission frequency
• Transmission range up to 30 m (range may be shorter
based on interference present)
• Temperature range: -20°C to 70°C (-4°F to 158°F)
• Temperature range via sensor probe: -40°C to 70°C
(-40°F to 158°F)
• Temperature tolerance: +/- 1.1°C (+/- 2°F)
• Table top or wall mount
• Requires 2 AAA batteries
Battery installation and setup
• Position the remote sensor near the base station.
• Open the battery compartment at the back of the
base station and insert 2 AAA batteries according to
the polarity markings.
• Replace the battery compartment cover.
• Press the UP C/F button at the back of the unit to
display the temperature in °C or °F.
• The RF signal icon (located to the left of the outdoor
temperature display) will flash for 5 minutes, inicating
that the base station is ready to pick up the RF signal
from the remote sensor.
Register the remote sensor
• Open the battery compartment at the back of the
remote sensor and slide the channel selector switch
to your desired channel. For the first remote you may
select any channel, for additional remotes select any
unused channel.
• Insert (2) AAA batteries according to the polarity
markings. Be sure to install the batteries in the
remote within the time that the RF signal icon is
flashing on the base station.
• Replace the battery compartment cover.
• If you have registered more than one sensor, press
the CHANNEL button to select the remote channel
you want displayed permanently on the base station.
Or press CHANNEL until you observe a circular arrow
on the base station LCD display under the channel
number. The unit will then auto-scroll, changing from
channel to channel every 5 second.
Register a remote sensor when the RF signal
icon is not showing
To register a remote sensor when the RF signal icon is
not showing on the base station LCD:
• Press and hold the CHANNEL button for 3-4 seconds
until the RF signal icon is showing.
• Install the batteries in the new remote sensor or if the
batteries have already been installed, press either the
TX or RESET button, which are located inside the
remote battery compartment.
Note:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon zinc), or
rechargeable (nickel cadmium) batteries.
• For maximum performance in nomal conditions we
recommend using good quality alkaline batteries.
When temperatures are below 0°C, alkaline
batteries can lose power resulting in a loss of remote
transmission. If you reside in an area that
experiences frequent temperatures near or below
0°F, we recommend using lithium batteries to
minimize the loss off transmission.
Locating the base station and remote sensor
• Chosse a suitable place for the base station and
remote outdoor sensor, within the transmission
distance.
• Place the base unit near a window, but away from
direct sunlight or sources of heat or air conditioning
to ensure accurate temperature readings.
• The remote sensor is water resistant, but not
waterproof. Locate the sensor out of direct sunlight,
in an area where it will not be exposed to rain, snow
or ice.
• The location you chosse is critical for maximizing the
transmission range. The remote sensor is desighned
to transmit up to 100 ft. unimpeded. Transmitting
through walls, metal doors and metal framed
windows may reduce the transmission range. To
optimize the transmission distance, the remote should
be positioned in a location that minimizes these
obstructions. Interference from other sources such
as home security systems, wireless doorbells
and wireless home entertainment equipment may
interrupt the transmission signal temporarily.
12/24 hour clock selection
In the normal time display mode, press the DOWN 12/24
button to display the time in 12 hour or 24 hour format.
(In 12 hour format AM or PM will show at the left of the
time).
Setting time and date
• Press the SET button for 2-3 seconds until the hour is
flashing.
• Press UP or DOWN to set the hour.
• Press SET and the minutes will be flashing.
• Press UP or DOWN to set the minutes.
• Press SET and the month will be flashing.
• Press UP or DOWN to set the month.
• Press SET and the date will be flashing.
• Press UP or DOWN to set the date.
• Press SET and the year will be flashing.
• Press UP or DOWN to set the year.
• Press SET to lock in the settings and return to the
nomal time display.
• If no buttons are pressed within 20 seconds, the unit
will revert to the nomal time display.
• In any setting mode you can press the CHANNEL
button to revert to the normal time display.
Note:
Use the MODE button to scroll through the various
displays. Starting from the nomal time display, press
MODE to view alarm time 1, alarm time2, countdown
timer, return to normal time. If the display is in any mode
other than normal time and no buttons are pushed,
within 20 seconds the LCD display will revert to the
normal time display.
Display the Calendar
In normal display mode press the SET button once
to display the time with seconds, press SET again to
display the date, press SET again to return the normal
time display.
Setting the Alarm Time
Two different alarm times can be get, Alarm 1 and
Alarm 2.
• To set Alarm 1; In normal time mode, press the MODE
button once and the Alarm 1 time and icon /a1) will
show.
• Press the SET button for 2-3 seconds until the alarm
hour flashes.
• Press UP or DOWN to set the alarm hour.
• Press SET and the minutes will be flashing.
• Press UP o DOWN to set the alarm minutes.
• Press SET to return to normal time display.
• To set Alarm 2; In moment time mode, press MODE
twice and the Alarm 2 time and icon (A2) will show.
• Follow the same setting sequence as for Alarm 1.
7