Care And Cleaning; Technical Data - Conrad DC9257AP Bedienungsanleitung

• Barcodes are available for the following countries: USA, Denmark, France, Italy, Japan, Finland,
Germany and Norway.
• Exit configuration mode by scanning the End Configuration barcode.
f) Symbology settings
• Turn on the barcode scanner.
• Press gently on the scan trigger (4) to start a scan.
• Enable configuration mode by scanning the Start Configuration barcode in the quick start guide.
• Select the desired symbology settings from the table in the quick start guide.
• Enable a symbology by scanning the "ENABLE" barcode.
• Disable a symbology by scanning the "DISABLE" barcode.
• Exit configuration mode by scanning the End Configuration barcode.
1D Symbologies – 1
CODE 39 ENABLE / DISABLE
CODE 39 FULL ASCII ENABLE / DISABLE
CODE 39 Transmit Start/Stop Character
ENABLE / DISABLE
UPC-E ENABLE / DISABLE
UPC-A ENABLE / DISABLE
Interleaved 25
Matrix 25
Interleaved 25
Industrial 25
Code 93 ENABLE / DISABLE
1D Symbologies – 2
CODABAR ENABLE / DISABLE
CODE 128 ENABLE / DISABLE
GS1-128 UCC/EAN-128 ENABLE / DISABLE
MSI ENABLE / DISABLE
1D Symbologies – 3
CODE 11 ENABLE / DISABLE
GS1-Databar (RSS) ENABLE / DISABLE
GS1-Databar (RSS-Limited) ENABLE / DISABLE
GS1-Databar (RSS-Expand) ENABLE / DISABLE
ISSN ENABLE / DISABLE
ISBN ENABLE / DISABLE
EAN-8 ENABLE / DISABLE
EAN-13 ENABLE / DISABLE
g) Configuring the keystroke delay
• Enable configuration mode by scanning the Start Configuration barcode in the quick start guide.
• To configure the keystroke delay, scan the No Delay, Short Delay (5 ms delay), Medium Delay
(10 ms delay ) or Long Delay (15 ms delay) configuration codes in the "Inter-Keystroke Delay
(For USB HID only)" section in the quick start guide.
• Exit configuration mode by scanning the End Configuration barcode.
h) Restoring default settings
• Scan the configuration codes A1 to A7 (in ascending order) in the "Reset Configuration to Defaults"
section in the quick start guide.
• The default settings will be restored.
Scanning barcodes
Ensure that you select the correct keyboard settings on your mobile device. The following
symbols are usually only supported for the "US" country settings: @ | $ # { } [ ] = / ' \ < > ~
• Open an application or document on your mobile phone. After it has been read successfully, the barcode
will be inserted into the position where the cursor blinks.
• Move the sliding switch (3) to the "O" position.
• Position the scanner at a sufficient distance and an angle of 30 - 60° to the barcode.
Enable/disable CODE 39
Enable/disable CODE 39 FULL ASCII
Enable/disable CODE 39 Transmit Start/Stop
Character
Enable/disable UPC-E
Enable/disable UPC-A
Enable/disable Interleaved 25
Enable/disable Matrix 25
Enable/disable Interleaved 25
Enable/disable Industrial 25
Enable/disable CODE 93
Enable/disable CODABAR
Enable/disable CODE 128
Enable/disable GS1-128/UCC /EAN-128
Enable/disable MSI
Enable/disable CODE 11
Enable/disable GS1-Databar (RSS)
Enable/disable GS1-Databar (RSS-Limited)
Enable/disable GS1-Databar (RSS-Expand)
Enable/disable ISSN
Enable/disable ISBN
Enable/disable EAN-8
Enable/disable EAN-13
90°
• Press gently on the scan trigger (4) to start the scan process.
• Depending on the size and specification of the barcode, you may need to adjust the distance between the
barcode and the scanner.
• Move the sliding switch to the "C" position after use.
You will hear a beep when the barcode scanner successfully reads the barcode. A different
sound will be played if the scanner fails to read the barcode. Please note that the beep tones for
normal barcodes and configuration barcodes are different to enable you to distinguish between
the two processes.
Tips & important information
• Ensure that the barcode is clean before scanning it.
• The barcode must be fully visible.
• Keep the barcode scanner at the specified distance and angle from the barcode.
• Hold the barcode scanner in the correct position.
• To prevent incorrect results, check the settings each time you turn on the barcode scanner.

Care and cleaning

• Before cleaning the scanner, disconnect it from the power supply. Ensure that the scanning unit is not
connected to the rechargeable battery in the holder.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the
casing or even impair the functioning of the product.
• Use a dry, lint-free cloth to clean the product. Do not press too hard on the surface when cleaning to avoid
scratch marks.
• Dust can be easily removed using a clean long-haired brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

Operating voltage ................................. 5 V/DC
Charging current ................................... Max. 500 mA
Internal rechargeable battery ................ Built-in Li-ion battery, 3.7 V, 900 mAh
Supported mobile devices .................... 10.16 to 15.24 cm (display size)
USB connection .................................... Micro USB
Scanner ................................................ CCD Sensor (long distance sensor)
Scan element type ............................... Red LED (610 nm - 640 nm wavelength)
Scan speed ........................................... 300 scans/second
Best resolution ...................................... 4 mil
Depth of field ........................................ UPCA 13 mil, (50 mm - 620 mm)
EAN13 13 mil, (50 mm - 610 mm)
Scanning angle ..................................... Pitch ±60° @ 0° Roll and 0° Skew, Roll ±30° @ Pitch and 0°
Skew, Skew ±60° @ Roll and 0° Pitch
Required contrast ................................. ≥ 30 %
Symbologies ......................................... EAN-13, EAN-8, UPC-A, UPC-E, ISBN/ISSN, Codabar, Code 128,
Code 93, ITF-6, ITF-14, Interleaved 2 of 5, Industrial 2 of 5,
Matrix 2 of 5, GS1 Databar, Code 39, Code 11, MSI
Supported operating systems ............... Android 2.x, Android 3.x, Android 4.x, Android 5.x,
Android 6.x (mobile device hardware must support OTG)
Operating conditions ............................. 0 to +50 °C, 5 – 95 % RH (non-condensing)
Storage conditions ................................ -10 to +60 °C, 5 – 95 % RH (non-condensing)
Dimensions (W x H x D) ....................... 52.5 x 125 x 32.5 mm
Weight .................................................. Approx. 82 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
Hold the scanner at the correct angle to the barcode.
Never hold the scanner at right angles to the barcode.
*1435467_v1_0616_02_DS_m_4L_(2)