Maintenance - AEG us 1300 xe Gebrauchsanleitung

TECHNICAL DATA
Rated input ..............................................................................
Output ......................................................................................
Stroke rate under no-load ........................................................
Lengths of stroke .....................................................................
Weight without cable ...............................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) ..........................................
Sound power level (K = 3 dB(A)) ..............................................
Measured values determined according to EN 60 745.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Wear ear protectors. Exposure to noise can cause hearing
loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a „live" wire may make exposed metal
parts of the power tool „live" and shock the operator.
open air must be connected via a current surge preventing
switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must first be drilled with a hole
corresponding to the size of the saw blade.
Always place the guide shoe on the workpiece when
sawing.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It cuts curves
and can cut flush to a surface.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents: EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC
Manager Product Development
11 ENGLISH
Volker Siegle
.......................1300 W
.........................650 W
....................0-2800 min
-1
...........................30 mm
..........................3,8 kg
............................... m/s
2
............................... dB (A)
............................... dB (A)
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all
times.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Milwaukee Electric Tool,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together
with household waste material! In
observance of European Directive 2002/96/
EC on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling
facility.