Makita UA003G Betriebsanleitung Seite 18

2. Lift up the guide bar tip slightly and adjust the
chain tension. Turn the chain adjusting screw counter-
clockwise to tighten, turn it clockwise to loosen.
Tighten the saw chain until the lower side of the saw
chain fits in the guide bar rail as illustrated.
► Fig.13: 1. Guide bar 2. Saw chain 3. Chain adjust-
ing screw
3. Keep holding the guide bar lightly and attach the
sprocket cover.
Make sure that the saw chain does not loose at the
lower side.
4. Tighten the retaining nut to secure the sprocket
cover.
► Fig.14: 1. Retaining nut
Installing or removing the angled
attachment
Optional accessory
CAUTION:
Before installing or removing the
angled attachment, be sure to attach the guide
bar cover to the tool.
You can change the angle of the tool head by attaching
the angled attachment to the tool.
1. Attach the guide bar cover to the tool.
2. Loosen 2 bolts with the hex wrench, and then
remove the pipe and sleeves from the head of the tool.
► Fig.15: 1. Sleeve 2. Bolt
3. Remove the caps from the angled attachment.
► Fig.16: 1. Cap
4. Align the hole on the sleeve with that on the pipe,
and then attach 2 sleeves to the pipe. Align the hole on
the sleeve with that on the attachment, and then insert
the pipe into the attachment.
► Fig.17: 1. Hole 2. Bolt 3. Sleeve 4. Pipe
5. Tighten 2 bolts to fix the attachment.
► Fig.18: 1. Bolt
6. Attach the head of the tool to the attachment.
To fix the head of the tool vertically, fix the attachment
by tightening the bolt to the hole on the attachment
shown in the figure, and then tighten the other bolt.
► Fig.19: 1. Bolt 2. Hole
To fix the head of the tool horizontally, fix the attachment
by tightening the bolt to the hole on the attachment
shown in the figure, and then tighten the other bolt.
► Fig.20: 1. Bolt 2. Hole
To remove the angled attachment, perform the installa-
tion procedure in reverse.
OPERATION
Lubrication
NOTICE:
When filling the chain oil for the first time,
or refilling the tank after it has been completely emp-
tied, add oil up to the bottom edge of the filler neck.
The oil delivery may otherwise be impaired.
NOTICE:
Use the saw chain oil exclusively for Makita
chain saws or equivalent oil available in the market.
NOTICE:
Never use oil including dust and parti-
cles or volatile oil.
NOTICE:
When pruning trees, use botanical oil.
Mineral oil may harm trees.
NOTICE:
Before the cutting operation, make sure
that the oil tank cap is tightened securely.
Saw chain is automatically lubricated when the tool is in opera-
tion. Check the amount of remaining oil in the oil tank periodically.
► Fig.21: 1. Oil tank
To refill the tank, place the tool on a flat surface, then push the
button on the oil tank cap so that the button on the other side
stands up, and then remove the oil tank cap by turning it.
The proper amount of oil is 160 ml. After refilling the tank,
make sure that the oil tank cap is tightened securely.
► Fig.22: 1. Oil tank cap 2. Tighten 3. Loosen
NOTE: If it is difficult to remove the oil tank cap,
insert the box wrench into the slot of the oil tank
cap, and then remove the oil tank cap by turning it
counterclockwise.
► Fig.23: 1. Slot 2. Box wrench
After refilling, hold the tool away from the tree. Start it
and wait until lubrication on saw chain is adequate.
► Fig.24
Attaching the shoulder harness
CAUTION:
When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
If you put on the shoulder harness included in the tool pack-
age and the shoulder harness of the backpack-type power
supply at the same time, removing the tool or backpack-type
power supply is difficult in case of an emergency, and it may
cause an accident or injury. For the recommended hanging
band, ask Makita Authorized Service Centers.
CAUTION:
Always use the shoulder harness
attached to the tool. Before operation, adjust the shoul-
der harness according to the user size to prevent fatigue.
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
CAUTION:
Before operation, make sure that the
buckle of the shoulder harness is fastened firmly.
CAUTION:
Always use the shoulder harness dedi-
cated to this tool. Do not use other shoulder harnesses.
18 ENGLISH