Herunterladen Inhalt Inhalt Diese Seite drucken

Safety Instructions; Additional Safety Rules For Tool - Makita 2106 Betriebsanleitung

Tragbare bandsäge
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

SAFETY INSTRUCTIONS

WARNING:
When using electric tools, basic safety precautions,
including the following, should always be followed to
reduce the risk of fire, electric shock and personal
injury. Read all these instructions before operating
this product and save these instructions.
For safe operations:
1. Keep work area clean.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use power
tools in damp or wet locations. Keep work area well lit.
Do not use power tools where there is risk to cause
fire or explosion.
3. Guard against electric shock.
Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away.
Do not let visitors touch the tool or extension cord. All
visitors should be kept away from work area.
5. Store idle tools.
When not in use, tools should be stored in a dry, high
or locked up place, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate for which it
was intended.
7. Use the right tool.
Do not force small tools or attachments to do the job of
a heavy duty tool. Do not use tools for purposes not
intended; for example, do not use circular saws to cut
tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, they can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protecting hair covering to contain long hair.
9. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting operation is
dusty.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11. Do not abuse the cord.
Never carry the tool by the cord or yank it to discon-
nect it from the socket. Keep the cord away from heat,
oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold the work. It is safer than
using your hand and it frees both hands to operate the
tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and
changing accessories. Inspect tool cord periodically
and if damaged have it repaired by an authorized ser-
vice facility. Inspect extension cords periodically and
replace, if damaged. Keep handles dry, clean and free
from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to deter-
mine that it will operate properly and perform its
intended function. Check for alignment of moving
parts, free running of moving parts, breakage of parts,
mounting and any other conditions that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by an autho-
rized service center unless otherwise indicated in this
instruction manual. Have defective switches replaced
by an authorized service facility. Do not use the tool if
the switch does not turn it on and off.
21. Warning.
The use of any accessory or attachment, other than
those recommended in this instruction manual or the
catalog, may present a risk of personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.
ADDITIONAL SAFETY RULES
FOR TOOL
1. Use only blades which are 1,140 mm long, 13 mm
wide, and 0.5 mm thick.
2. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
3. Secure the workpiece firmly. When cutting a bun-
dle of workpieces, be sure that all workpieces are
secured together firmly before cutting.
4. Cutting workpieces covered with oil can cause the
blade to come off unexpectedly. Wipe off all
excess oil from workpieces before cutting.
5. Never use the cutting oil as a cutting lubricant.
Use only Makita cutting wax.
6. Do not wear gloves during operation.
7. Hold the tool firmly with both hands.
8. Keep hands away from rotating parts.
5

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis