HIKMICRO M-Serie Kurzanleitung Seite 7

l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux.
(ii) Le gain d'antenne maximal autorisé pour les appareils
dans les bandes 5250-5350 MHz et 5470-5725 MHz
doivent respecter le pire limiter; et
(iii) Le gain d'antenne maximal autorisé pour les appareils
dans la bande 5725-5825 MHz doivent respecter le pire
limites spécifiées pour le point-à-point et l'exploitation
non point à point, le cas échéant.
Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that
these radars could cause interference and/or damage to
LE-LAN devices.
Les utilisateurs de radars de haute puissance sont
désignés utilisateurs principaux (c.-à-d., qu'ils ont la
priorité) pour les bandes 5250-5350 MHz et 5650-5850
MHz et que ces radars pourraient causer du brouillage
et/ou des dommages aux dispositifs LAN-EL.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
● Use of the product must be in strict compliance with
the local electrical safety regulations.
Transportation
● Keep the device in original or similar packaging while
transporting it.
● Keep all wrappers after unpacking them for future use.
In case of any failure occurred, you need to return the
device to the factory with the original wrapper.
Transportation without the original wrapper may result
in damage on the device and the company shall not
take any responsibilities.
● Do not drop the product or subject it to physical shock.
Keep the device away from magnetic interference.
Power Supply
● The input voltage should meet the limited energy
circuit (5 VDC, 2 A) according to the IEC61010-1
standard. Please refer to technical specifications for
detailed information.
● Make sure the plug is properly connected to the power
socket.
● DO NOT connect multiple devices to one power adapter,
to avoid over-heating or fire hazards caused by
overload.
● Use the power adapter provided by qualified
manufacturer. Refer to the product specification for
detailed power requirements.
Battery
● Improper use or replacement of the battery may result
in explosion hazard. Replace with the same or
equivalent type only. The battery type is
E97-13-1S1P26650. Dispose of used batteries in
conformance with the instructions provided by the
battery manufacturer.
● Do not charge other battery types with the supplied
charger. Confirm there is no flammable material within
2 m of the charger during charging.
● For long-term storage of the battery, make sure it is
fully charged every half year to ensure the battery
quality. Otherwise, damage may occur.
● DO NOT place the battery near heating or fire source.
Avoid direct sunlight.
● DO NOT swallow the battery to avoid chemical burns.
● DO NOT place the battery in the reach of children.
● CAUTION: Risk of explosion if the battery is replaced by
an incorrect type.
● Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result
in an explosion.
● Do not subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas.
● When the device is powered off and the RTC battery is
full, the time settings can be kept for 2 months.
● In the first use, power on the device and charge the RTC
battery with the lithium battery for more than 8 hours.
● The battery voltage is 3.7 V, and the battery capacity is
5000 mAh.
● The battery is certified by UL2054.
Maintenance
● If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
● Wipe the device gently with a clean cloth and a small
quantity of ethanol, if necessary.
● If the device is used in a manner not specified by the
manufacturer, the protection provided by the device
may be impaired.
● Please notice that the current limit of USB 3.0
PowerShare port may vary with the PC brand, which is
likely to result in incompatibility issue. Therefore, it's
advised to use regular USB 3.0 or USB 2.0 port if the
USB device fails to be recognized by PC via USB 3.0
PowerShare port.
● We recommend you send the device back for
calibration once a year, and please contact the local
dealer for the information on maintenance points.
● Your camera will periodically perform a self-calibration
to optimize image quality and measurement accuracy.
In this process the image will pause briefly and you will
hear a "click" as a shutter moves in front of the
detector. The self-calibration will be more frequent
during the startup or in very cold or hot environments.
This is a normal part of operation to ensure optimum
performance for your camera.
Using Environment
● DO NOT expose the device to extremely hot, cold, dusty,
corrosive, saline-alkali, or damp environments. Make
sure the running environment meets the requirement
of the device. The operating temperature shall be
-10 °C to 50 °C (14 °F to 122 °F), and the operating
humidity shall be 90% or less.
● This device can only be safely used in the region below
2000 meters above the sea level.
● Place the device in a dry and well-ventilated
environment.
● DO NOT expose the device to high electromagnetic
radiation or dusty environments.
● DO NOT aim the lens at the sun or any other bright
light.
● When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may
burn out.
● The device is suitable for indoor conditions.
● The pollution degree is 2.
● Overvoltage category: 0 for Handheld Thermography
Camera.
● Overvoltage category: II for power adapter.
5