Grounding Installation; Control Panel; Preparation Before Use - Hendi 239278 Benutzerhandbuch

- bed and breakfast type environment.
• The appliance is designed for cooking a variety of food via
heating the suitable cookware. Any other use may lead to
damage to the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed as a misuse of the device. The user shall be solely
liable for improper use of the device.

Grounding installation

This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.

Control panel

(Fig.1 on page 3)
1. ON/Standby button
2. Timer function with indicator light
3. Increase setting: Time / temperature / power
4. Digital display
5. Decrease setting: Time / temperature / power
6. Power function with indicator light
7. Temperature function with indicator light

Preparation before use

• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accesso-
ries. In case of incomplete or damaged delivery, please contact
the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See == >
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
• Place a suitable pan or pot at the centre of the heating surface
of the appliance. (See --> Suitable cooking equipment).
Note: Do not place empty pan as this may damage the pan and
the appliance.
• Connect the power plug to a suitable electrical supply outlet.
On/Standby button (1) will be light up and the appliance now
in Standby mode.
• Then, switch On the appliance by pressing On/Standby button
(1) and Power button (6) will flash.
• Next, choose to press either the power button (6) or temper-
ature button (7) to start cooking. If the timer button (2) is not
set, the appliance will operate continuously.
• Once you have finished cooking, switch to Standby mode by
pressing the On/Standby button (1). The digital display (4) and
all buttons will go off except On/Standby button (1).
Note: If no any button on the control panel is pressed during
operation for 2 hours, the appliance will then switch to Standby
mode automatically.
Setting Power level
• During operation, press the power button (6) to activate. The
indicator light (6) will light up.
• Use the increase setting (3) or decrease setting button (5) to
increase or decrease the power level (Range: 100W ~ 2,000W).
Default setting is 100W. Higher power level is suitable for
steaming.
Setting Temperature level
• During operation, press the temperature button (7) to acti-
vate. The indicator light (7) will light up.
• Use the increase setting (3) or decrease setting button (5) to
increase or decrease the temperature level (Range: 35°C ~
240°C). Default setting is 100°C. Higher temperature level is
suitable for roasting, grilling or frying.
Setting Timer
• After power or temperature setting for cooking, you can opt
for timer setting. Press the timer button (2) to activate. The
indicator light (2) lights up.
• Use the increase setting (3) or decrease setting button (5) to
increase or decrease the cooking time (Range: 0 min ~ 180
mins). Default setting is 0 min.
• When the timer is set, it will be stored automatically within 5
seconds. The appliance will then start operation. It will dis-
play the remaining time and the power setting / temperature
setting alternately on the display (4).
• The appliance will go into Standby mode when the set time
is elapsed.
• If the set time is reduced to "0 min" manually, the appliance
will go into Standby mode instantly.
Note:
1. Press and hold the increase setting button (3) or decrease
setting button (5) for fast adjustment.
2. After an extended period of operation, it is normal for the
cooling fan inside to continue running in Standby mode for
some time. Before unplug the appliance, wait until the cool-
ing fan stops running.
3. The appliance's surface is still hot after switch to Standby
mode. Wait completely cool down before touching.
Suitable cooking equipment
Suitable
Bottom of Flat bottom
cookware (Fig.2 on page 3)
Material Cookware with iron,
cast iron, magnetic
stainless steel or
enamelled iron
bottom.
Diameter of Between 12 cm and
the bottom 22 cm.
Type of Cookware with a
cookware bottom thickness over
1.5 mm.
GB
Not suitable
Curved, uneven,
rounded bottom
(Fig.3 on page 3)
Cookware with
ceramic, glass, copper,
bronze, or aluminium
bottom.
Less than 12 cm or
more than 22 cm.
Completely closed
containers or cans.
7